Toyota GT86 Front V2 Lock Kit for Front Rack

$2,350.00
excluding VAT
In stock
SKU
WF8601
or View Spares

GT86 front V2 Lock kit for front rack is made of high strength steel. It is a little heavier than the V1 kit, but it is stronger, stiffer and has more adjustment options and improved kinematics. Due to the boxer engine, the original steering rack location is very unsuitable for drifting, therefore the steering rack has been moved infront of the crossmember with the possibility to use any rear sump engine you like. The main advantage of the front steering rack location is more precise steering feel on big angle that makes the car much easier to handle in extreme conditions. BMW E9X or Lexus LS (UCF30) steering rack is needed to be used with this kit to replace the original electric power steering.

Want to know how does Wisefab Lock kit fits your driftcar check the link below CHECK FITMENT or here!

Check out the rear V2 suspension kit for Toyota GT86

Scroll down to order your spare parts conviently right here!

Here is our recommended alignment parameters:
Toe in/out: If Ackermann is 0 or negative then toe is 2mm out. If Ackermann is positive then toe is 0
Camber: -6
Caster: 5,5

  • 65+ degrees of usable steering angle
  • Adjustable Ackermann angle. You can tune your steering geometry towards positive or negative Ackermann in just a few minutes without messing up the alignment. Ackermann adjustment washers are included in the kit.
  • Knuckles and control arms are made of high strength steel. All parts are machined after welding for maximum precision. 
  • CrMo rod ends and sphericals used instead of OEM bushings
  • Higher roll center (RC)
    With our knuckle, the ball joint is lowered, which brings the front RC up on a lowered car, providing higher roll stiffness. This allows to remove the front anti roll-bar (sway bar) that is quite difficult to package with high steering angle.
  • Good camber control and minimal bump steer with high steering angle.
    On drift cars the dynamic camber and bump steer is much more important than static. With our kinematics we have assured that the camber will provide very good front grip and bump steer is minimal throughout the steering range.
  • Steering jacking control
    During drifting, when steering angle is increased, jacking is also bigger, even with the same geometry it could become a problem. We have changed the geometry in a way that doesn't cause any handling issues.
  • Consistent and predictable self-alignment torque. 
    Caster is not the only important parameter to provide sufficient self-alignment torque, especially at high lock. It's the combination of different parameters to maintain consistent trail and self-alignment torque. With our setup the steering wheel turns always to the direction of movement and doesn't get stuck at full lock.

Kit includes:

  • Pre-set lower control arms
  • Knuckles with hardware
  • Assembeled tie rods
  • Pre-set coilover camber plates
  • Front position rack relocating kit
  • Crossmember supports
  • Installation guide

 

Other information:

  • BMW and Lexus steering rack attachments and crossmember inserts are included in the kit. To modify the crossmember some DIY cutting and welding needs to be done. Please make sure to follow the installation manual.
  • This kit assumes coilovers for enough clearance
  • Dependent on rim width and ET, wider fenders or fender flares are needed.
  • Due to extremely wide engine bay on Subaru BRZ, we recommend using tires no bigger than 605mm (215/40R17, 225/40R17, 225/35R18, 235/35R18)
  • With tire diameter up to 635mm (215/45R17, 225/45R17, 235/40R17, 225/40R18 etc) and lowered ride height the inner wheel wells need to be slightly modified.
  • Recommend rim size 18" but some 17" might also fit.
  • Depending on the rim diameter the recommended backspacing is 150-160mm (7" ET45; 8" ET35; 9" ET25). If ET is smaller, then wheels stay more outwards, if ET is bigger, then spacers need to be used.
More Information
Make Toyota
Field Drift
Placement Front
Prodmaster Name V2 Lock Kit for Front Rack

Spare parts

All
Complete parts
Toyota GT86 V2 Front Knuckle Left
Toyota GT86 V2 Front Knuckle Right
Toyota GT86 V2 Front Left Lower Control Arm
Toyota GT86 V2 Front Right Lower Control Arm
V2 Tie Rod Assembly For Front Rack
Left Subframe Support
Right Subframe Support
Toyota GT86 V2 Front Camber Plate Left
Toyota GT86 V2 Front Camber Plate Right

Complete parts

Complete parts

1
Toyota GT86 V2 Front Knuckle Left
WF8601_100LA
$700.00
excluding VAT
1
Toyota GT86 V2 Front Knuckle Right
WF8601_100RA
$700.00
excluding VAT
2
Toyota GT86 V2 Front Left Lower Control Arm
WF8601_200LA
$510.00
excluding VAT
2
Toyota GT86 V2 Front Right Lower Control Arm
WF8601_200RA
$510.00
excluding VAT
3
V2 Tie Rod Assembly For Front Rack
WF8601_600A
$115.00
excluding VAT
4
Subframe Support
Left
WF860_400L
$75.00
excluding VAT
Right
WF860_400R
$75.00
excluding VAT
5
Toyota GT86 V2 Front Camber Plate Left
WF8601_500LA
$220.00
excluding VAT
5
Toyota GT86 V2 Front Camber Plate Right
WF8601_500RA
$220.00
excluding VAT

Toyota GT86 V2 Front Knuckle Left

Toyota GT86 V2 Front Knuckle Left

1
Toyota GT86 V2 Front Knuckle Left
WF8601_100LA
$700.00
excluding VAT
2
Hub Center Ring
WF862_905
$24.00
excluding VAT
3
Bolt Allen M12x1.25x 70 RH 12.9 ST DIN912
B01212150070R4SD912
$0.00
excluding VAT
4
Washer FlatSmall M12 ZN DIN433
B03212NAZD433
$2.10
excluding VAT
5
BushingT ID12 OD28 h11
WF180_905
$12.00
excluding VAT
6
Ackermann Washer Round 0 offset
WF013_140
$10.00
excluding VAT
7
Ackermann Washer Round 3 Offset
WF080_142
$10.00
excluding VAT
8
Ackermann Washer Round 6 Offset
WF080_144
$10.00
excluding VAT
9
Bolt Hex M10x1.5x 65 RH 10.9 ST DIN 931
B01110150065R3SD931
$4.00
excluding VAT
10
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$2.10
excluding VAT
11
BushingT ID 8 OD22 h51 Excentric Lock Stopper
WF370_950
$16.00
excluding VAT
12
Bolt Hex M 8x1.25x 70 RH 8.8 ZN DIN 931
B01108125070R2ZD931
$2.10
excluding VAT
13
Washer Flat M 8 ZN DIN125
B03108NAZD125
$2.10
excluding VAT

Toyota GT86 V2 Front Knuckle Right

Toyota GT86 V2 Front Knuckle Right

1
Toyota GT86 V2 Front Knuckle Right
WF8601_100RA
$700.00
excluding VAT
2
Hub Center Ring
WF862_905
$24.00
excluding VAT
3
Bolt Allen M12x1.25x 70 RH 12.9 ST DIN912
B01212150070R4SD912
$0.00
excluding VAT
4
Washer FlatSmall M12 ZN DIN433
B03212NAZD433
$2.10
excluding VAT
5
BushingT ID12 OD28 h11
WF180_905
$12.00
excluding VAT
6
Ackermann Washer Round 0 offset
WF013_140
$10.00
excluding VAT
7
Ackermann Washer Round 3 Offset
WF080_142
$10.00
excluding VAT
8
Ackermann Washer Round 6 Offset
WF080_144
$10.00
excluding VAT
9
Bolt Hex M10x1.5x 65 RH 10.9 ST DIN 931
B01110150065R3SD931
$4.00
excluding VAT
10
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$2.10
excluding VAT
11
BushingT ID 8 OD22 h51 Excentric Lock Stopper
WF370_950
$16.00
excluding VAT
12
Bolt Hex M 8x1.25x 70 RH 8.8 ZN DIN 931
B01108125070R2ZD931
$2.10
excluding VAT
13
Washer Flat M 8 ZN DIN125
B03108NAZD125
$2.10
excluding VAT

Toyota GT86 V2 Front Left Lower Control Arm

Toyota GT86 V2 Front Left Lower Control Arm

1
Toyota GT86 V2 Front Left Lower Control Arm
WF8601_200LA
$510.00
excluding VAT
2
Control Arm Rear Fixing
WF8601_210A
$180.00
excluding VAT
3
Spacer ID14 OD16 h29
WF860_902
$12.00
excluding VAT
4
Spacer ID14 OD16 h10
WF036_903
$12.00
excluding VAT
5
Bolt Hex M14x1.5x120 RH 10.9 ST DIN 960
B01114150120R3SD960
$12.00
excluding VAT
6
Washer Flat M14 ZN DIN125
B03114NAZD125
$2.10
excluding VAT
7
Rod end 16x1.5 RH male CrMo
SRODEND16X1.5 RH M
$36.00
excluding VAT
8
Nut Thin M16x1.5 RH 8.8 ZN DIN936/439
B02316150R2ZD936/439
$4.00
excluding VAT
9
Spacer ID12 OD16 h18
WF136_903
$12.00
excluding VAT
10
Spherical ID16/OD32
SSPHERICAL 16/32
$35.00
excluding VAT
11
C-Clip InternalSTD d32 ST DIN472
B04132SD472
$2.10
excluding VAT
12
Spacer ID12 OD16 h10
WF013_903
$12.00
excluding VAT

Toyota GT86 V2 Front Right Lower Control Arm

Toyota GT86 V2 Front Right Lower Control Arm

1
Toyota GT86 V2 Front Right Lower Control Arm
WF8601_200RA
$510.00
excluding VAT
2
Control Arm Rear Fixing
WF8601_210A
$180.00
excluding VAT
3
Spacer ID14 OD16 h29
WF860_902
$12.00
excluding VAT
4
Spacer ID14 OD16 h10
WF036_903
$12.00
excluding VAT
5
Bolt Hex M14x1.5x120 RH 10.9 ST DIN 960
B01114150120R3SD960
$12.00
excluding VAT
6
Washer Flat M14 ZN DIN125
B03114NAZD125
$2.10
excluding VAT
7
Rod end 16x1.5 RH male CrMo
SRODEND16X1.5 RH M
$36.00
excluding VAT
8
Nut Thin M16x1.5 RH 8.8 ZN DIN936/439
B02316150R2ZD936/439
$4.00
excluding VAT
9
Spacer ID12 OD16 h18
WF136_903
$12.00
excluding VAT
10
Spherical ID16/OD32
SSPHERICAL 16/32
$35.00
excluding VAT
11
C-Clip InternalSTD d32 ST DIN472
B04132SD472
$2.10
excluding VAT
12
Spacer ID12 OD16 h10
WF013_903
$12.00
excluding VAT

V2 Tie Rod Assembly For Front Rack

V2 Tie Rod Assembly For Front Rack

1
V2 Tie Rod Assembly For Front Rack
WF8601_600A
$115.00
excluding VAT
2
Tie Rod Inner M14x1.5 M14x1.5 L400
STIEROD_M14_M14_L400
$30.00
excluding VAT
3
Rod end 14x1.5 RH female CrMo
SRODEND14X1.5 RH F
$36.00
excluding VAT
4
Spacer ID10 OD14 h11
WF013_901
$10.00
excluding VAT
5
Rack Extender M14x1.5 M18x1.5 L 46.5
WF8601_902
$0.00
excluding VAT

Left Subframe Support

Left Subframe Support

1
Subframe Support
Left
WF860_400L
$75.00
excluding VAT

Right Subframe Support

Right Subframe Support

1
Subframe Support
Right
WF860_400R
$75.00
excluding VAT

Toyota GT86 V2 Front Camber Plate Left

Toyota GT86 V2 Front Camber Plate Left

1
Toyota GT86 V2 Front Camber Plate Left
WF8601_500LA
$220.00
excluding VAT
2
Nut Hex Flange M 8x1.25 RH 8.8 ZN
B02508125R2ZD69238
$2.10
excluding VAT
3
Bolt Hex M 8x1.25x 16 RH 8.8 ZN DIN 933
B01108125016R2ZD933
$2.10
excluding VAT
4
Spherical ID18/OD35
SSPHERICAL 18/35
$36.00
excluding VAT
5
C-Clip InternalSTD d35 ST DIN472
B04135SD472
$2.10
excluding VAT

Toyota GT86 V2 Front Camber Plate Right

Toyota GT86 V2 Front Camber Plate Right

1
Toyota GT86 V2 Front Camber Plate Right
WF8601_500RA
$220.00
excluding VAT
2
Nut Hex Flange M 8x1.25 RH 8.8 ZN
B02508125R2ZD69238
$2.10
excluding VAT
3
Bolt Hex M 8x1.25x 16 RH 8.8 ZN DIN 933
B01108125016R2ZD933
$2.10
excluding VAT
4
Spherical ID18/OD35
SSPHERICAL 18/35
$36.00
excluding VAT
5
C-Clip InternalSTD d35 ST DIN472
B04135SD472
$2.10
excluding VAT
Wisefab Nissan 240sx
"’We started working together with Wisefab back in 2014 when we launched our Falken Tyres Nissan 240sx for European competition. Since then, we have enjoyed working closely with the engineers at Wisefab testing new products before going into production and have had a lot of success winning multiple championship worldwide. Thank you to everyone at Wisefab for believing in us and producing such top-quality products."
Nissan 240sx Drift
“When I first installed a Wisefab lock kit it truly opened the door for some more aggressive driving style. I quickly began to expect nothing less than the massive angle and performance that Wisefab provides and installed a lock kit on all (4) of my Nissan 240sx that I currently drift. Also, after testing what I though was a very competitive rear suspension solution against the latest Wisefab rear kit, I was blown away with the apparent grip gain the rear Wisefab kit yielded. I am so thankful that Wisefab has poured so much effort into creating a bolt on suspension solution that transforms a Nissan 240sx into what I believe is still the most competitive drift chassis in the world."
Nissan 240sx Lock kit
"I love the Wisefab suspension kits used on my competition and demo vehicles, they provide all the angle and grip we love along with the strength and durability we need to compete with the best!"
Toyota 86 Drift
"I wouldn't have half the results! Only by running Wisefab in my Toyota 86 it just makes the car handle so good and let's me adjust set up pretty easy which is a massive help going from track to track!"