Toyota Supra A90 Front Drift Angle Lock Kit

$2,850.00
excluding VAT
In stock
SKU
WFA90
or View Spares

The Toyota Supra A90 is one of the most discussed new cars around. Rear wheel drive together with turbocharged in-line six engine offers great potential for drifting. Here at Wisefab we have developed PRO level lock kit for this chassis. It has been tested in Japan and USA by the best drivers around and we are happy to offer this product now to our customers.

All the metal components on Wisefab A90 front suspension are from high strength steel, including sheet metal components, tubes, tube ends and rod end housings. Rod ends and spherical bearings are used, no rubber bushings.

Want to know how does Wisefab Lock kit fits your driftcar check below the link CHECK FITMENT or here!

Check out the 2020 Toyota Supra rear suspension kit!.

Scroll down to order your spare parts conviently right here!

Here is our recommended alignment parameters:
Toe in/out: If Ackermann is 0 or negative then toe is 2mm out. If Ackermann is positive then toe is 0
Camber: -7 +/-0,3
Caster: 6 +/-0,3

  • 65 degrees of lock, parallel steering.
    You could tune your steering geometry either towards positive or negative Ackermann in just a few minutes even at trackside without messing up an alignment.
    Ackermann adjustment kit included.
  • Adjustable lock stopper.
  • One piece lower control arm desing.
    Lower links are replaced with one arm. Drifting with higher steering angle the stiffness and packaging would become an issue. Therefore lower one piece arm is used.
  • Higher roll center (RC).
    On Wisefab knuckle, joints are dropped, which brings the front RC up on lowered car, providing higher roll stiffness and letting to remove the front anti roll bar (sway bar) that is quite difficult to package with that high lock angles. 
  • Very good camber control and minimal bump steer with high steering angles.
    On drift cars the dynamic camber and bump steer is much more important than static. With our kinematics we have assured that the camber would provide very good front grip and bump steer is minimal at all the range of steering.
  • Steering jacking control.
    During drifting, when steering angle is much bigger, jacking is also bigger, even with the same geometry and it could become a problem. We have changed the geometry that it doesn’t cause any handling issues.
  • Consistent and predictable self-alignment torque.
    Caster is not the only important parameter to provide sufficient self-alignment torque especially at high lock. It’s the combination of different parameters to maintain consistent trail and self-alignment torque. With our setup the steering wheel turns always to the direction of movement and doesn’t get stuck at full lock. 
  • Original wheelspeed sensor (ABS sensor) can be used.

Kit includes

  • Adjustable coilover upper mounts, Formula Drift compliance.
  • Knuckles with hardware.
  • Lower control arms.
  • Assembeled tie rods.
  • Brake adapters for M model brakes.
  • 45mm coilover adapter sleeve.
  • Installation guide.

Important details about component fitment

  • Wheel bearing: Front wheel bearing has to be sourced from BMW E90. Part number 31216765157. OEM can not be used.
  • Wheels: Wheel bearing has 5x120 PCD. This means that OEM wheels can not be used.
  • Brakes: We recommend using brakes from BMW E90 or E90 M3. OEM brakes caliper can be used with the supplied E90 M3 brake caliper adapter. Brake adapter may need some modification. OEM brake disc can not be used. When using OEM brake caliper suitable brake disc needs to be sourced. Make sure that the brake disc is centered in the caliper
  • Strut: Strut lower fixing diameter has to be 56 mm or 62 mm. OEM fixing diameter is 56 mm. Ride height adjustable coilovers must be used.
  • Steering rack: We do not recommend using the OEM steering rack but it can be used. If the steering rack is changed it has to be mounted exactly where the OEM steering rack was.
More Information
Make Toyota
Field Drift
Placement Front
Prodmaster Name Drift Angle Lock Kit
Wisefab fitment calculator
Make and Model
?
Fender Arch Height from Ground (mm)
Tire Width
Tire Height or Diameter
Rim Diameter
Rim Width
ET
Wheelspacer (mm)
Suspension selection
Suspension selection
OEM
WISEFAB
CUSTOM
 
1800 mm
1800 mm
Fender to Fender
1615 mm
1794 mm
Hub to Hub
-1 °
-7 °
Camber
8 °
6 °
Caster
-1 mm
-2 mm
Toe

Set your desired rim and tire parameters in our fitment calculator to have a better overview how Wisefab will transform your driftcar. Fender arch height is your indicator on ride height. Check the fitment and learn about missing fender gap before ordering widebody kit. In the custom section you can edit the fender to fender and wheelhub to wheelhub measurments according to your driftcar. Use the max width to check if your car will fit on your trailer. Have fun with this fitment calculator.

Spare parts

All
Complete parts
Left Knuckle
Right Knuckle
Left Lower Control Arm
Right Lower Control Arm
TieRod Assembly
M3 Brake Adapter
Top Mount
E90 Steering Rack Conversion Kit

Complete parts

Complete parts

1
Knuckle
Left
WFA90_100LA
$620.00
excluding VAT
Right
WFA90_100RA
$620.00
excluding VAT
2
Lower Control Arm
Left
WFA90_200LA
$530.00
excluding VAT
Right
WFA90_200RA
$530.00
excluding VAT
3
TieRod Assembly
WF220_600A
$120.00
excluding VAT
4
M3 Brake Adapter
WF900_400A
$100.00
excluding VAT
5
Top Mount
WFA90_500A
$230.00
excluding VAT
6
E90 Steering Rack Conversion Kit
WFA99_100A
$250.00
excluding VAT

Left Knuckle

Left Knuckle

2
Strut Adapter
WFA90_903
$39.00
excluding VAT
3
Bolt Hex M10x1.5x 70 RH 10.9 ST DIN 931
B01110150070R3SD931
$4.30
excluding VAT
4
Ackermann Washer Round 0 offset
WF013_140
$11.00
excluding VAT
5
Ackermann Washer Round 3 Offset
WF080_142
$11.00
excluding VAT
6
Ackermann Washer Round 6 Offset
WF080_144
$11.00
excluding VAT
7
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$2.30
excluding VAT
8
Bolt Hex M12x1.5x 60 RH 10.9 ST DIN 960
B01112150060R3SD960
$6.40
excluding VAT
9
Washer FlatSmall M12 ZN DIN433
B03212NAZD433
$2.30
excluding VAT
10
Bolt AllenButton M 8x1.25x 60 RH 8.8 ZN ISO7380
B01408125060R2ZI7380
$4.30
excluding VAT
11
BushingT ID 8 OD22 h41 Excentric Lock Stopper
WF350_950
$18.00
excluding VAT
12
Washer Flat M 8 ZN DIN125
B03108NAZD125
$2.30
excluding VAT
13
Washer Flat M12 ZN DIN125
B03112NAZD125
$2.30
excluding VAT

Right Knuckle

Right Knuckle

2
Strut Adapter
WFA90_903
$39.00
excluding VAT
3
Bolt Hex M10x1.5x 70 RH 10.9 ST DIN 931
B01110150070R3SD931
$4.30
excluding VAT
4
Ackermann Washer Round 0 offset
WF013_140
$11.00
excluding VAT
5
Ackermann Washer Round 3 Offset
WF080_142
$11.00
excluding VAT
6
Ackermann Washer Round 6 Offset
WF080_144
$11.00
excluding VAT
7
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$2.30
excluding VAT
8
Bolt Hex M12x1.5x 60 RH 10.9 ST DIN 960
B01112150060R3SD960
$6.40
excluding VAT
9
Washer FlatSmall M12 ZN DIN433
B03212NAZD433
$2.30
excluding VAT
10
Bolt AllenButton M 8x1.25x 60 RH 8.8 ZN ISO7380
B01408125060R2ZI7380
$4.30
excluding VAT
11
BushingT ID 8 OD22 h41 Excentric Lock Stopper
WF350_950
$18.00
excluding VAT
12
Washer Flat M 8 ZN DIN125
B03108NAZD125
$2.30
excluding VAT
13
Washer Flat M12 ZN DIN125
B03112NAZD125
$2.30
excluding VAT

Left Lower Control Arm

Left Lower Control Arm

2
Spacer ID12OD16h32
WFA90_902
$13.00
excluding VAT
3
Spacer ID12 OD16 h17.5
WFA90_901
$13.00
excluding VAT
4
Rod end 16x1.5 RH male CrMo
SRODEND16X1.5 RH M
$39.00
excluding VAT
5
Nut Thin M16x1.5 RH 8.8 ZN DIN936/439
B02316150R2ZD936/439
$4.30
excluding VAT
6
Spacer ID12 OD16 h10
WF013_903
$13.00
excluding VAT
7
C-Clip InternalSTD d32 ST DIN472
B04132SD472
$2.30
excluding VAT
8
Spherical ID16/OD32
SSPHERICAL 16/32
$38.00
excluding VAT
9
Lower Arm Mount
WF1401_210A
$150.00
excluding VAT

Right Lower Control Arm

Right Lower Control Arm

2
Spacer ID12OD16h32
WFA90_902
$13.00
excluding VAT
3
Spacer ID12 OD16 h17.5
WFA90_901
$13.00
excluding VAT
4
Rod end 16x1.5 RH male CrMo
SRODEND16X1.5 RH M
$39.00
excluding VAT
5
Nut Thin M16x1.5 RH 8.8 ZN DIN936/439
B02316150R2ZD936/439
$4.30
excluding VAT
6
Spacer ID12 OD16 h10
WF013_903
$13.00
excluding VAT
7
C-Clip InternalSTD d32 ST DIN472
B04132SD472
$2.30
excluding VAT
8
Spherical ID16/OD32
SSPHERICAL 16/32
$38.00
excluding VAT
9
Lower Arm Mount
WF1401_210A
$150.00
excluding VAT

TieRod Assembly

TieRod Assembly

2
Rack Extender M14x1.5 M18x1.5 L24
WF900_901
$35.00
excluding VAT
3
Tie Rod Inner M14x1.5 M14x1.5 L400
STIEROD_M14_M14_L400
$31.00
excluding VAT
4
Rod end 14x1.5 RH female CrMo
SRODEND14X1.5 RH F
$39.00
excluding VAT
5
Spacer ID10 OD14 h11
WF013_901
$11.00
excluding VAT
6
Rack Extender M14x1.5 M16x1.5 L24
WFR70_907
$35.00
excluding VAT

M3 Brake Adapter

M3 Brake Adapter

2
Bolt HexThin M12x1.50x 50 RH 10.9 ST SPC
WF900_908
$16.00
excluding VAT
3
Bolt Hex M12x1.5x 50 RH 10.9 ST DIN 961
B01112150050R3SD961
$6.40
excluding VAT
4
Nut Nylock M12x1.5 RH 8.8 ZN DIN985-8
B02212150R2ZD9858
$2.30
excluding VAT
5
Washer FlatSmall M12 ZN DIN433
B03212NAZD433
$2.30
excluding VAT

Top Mount

Top Mount

2
Bolt Hex M 8x1.25x 40 RH 8.8 ZN DIN 931
B01108125040R2ZD931
$2.30
excluding VAT
3
C-Clip InternalSTD d35 ST DIN472
B04135SD472
$2.30
excluding VAT
4
Spherical ID18/OD35
SSPHERICAL 18/35
$39.00
excluding VAT
5
Top Mount Spacer
WFA90_501
$39.00
excluding VAT
6
Nut Hex Flange M 8x1.25 RH 8.8 ZN
B02508125R2ZD69238
$2.30
excluding VAT

E90 Steering Rack Conversion Kit

E90 Steering Rack Conversion Kit

2
Bolt Hex M10x1.5x 65 RH 10.9 ST DIN 931
B01110150065R3SD931
$4.30
excluding VAT
3
Washer Flat M10 ZN DIN125
B03110NAZD125
$2.30
excluding VAT
4
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$2.30
excluding VAT
5
Bolt AllenFlat M10x1.50x 20 RH 8.8 ZN DIN7991
B01310150020R2ZD7991
$4.30
excluding VAT
Wisefab Nissan 240sx
"’We started working together with Wisefab back in 2014 when we launched our Falken Tyres Nissan 240sx for European competition. Since then, we have enjoyed working closely with the engineers at Wisefab testing new products before going into production and have had a lot of success winning multiple championship worldwide. Thank you to everyone at Wisefab for believing in us and producing such top-quality products."
Nissan 240sx Drift
“When I first installed a Wisefab lock kit it truly opened the door for some more aggressive driving style. I quickly began to expect nothing less than the massive angle and performance that Wisefab provides and installed a lock kit on all (4) of my Nissan 240sx that I currently drift. Also, after testing what I though was a very competitive rear suspension solution against the latest Wisefab rear kit, I was blown away with the apparent grip gain the rear Wisefab kit yielded. I am so thankful that Wisefab has poured so much effort into creating a bolt on suspension solution that transforms a Nissan 240sx into what I believe is still the most competitive drift chassis in the world."
Nissan 240sx Lock kit
"I love the Wisefab suspension kits used on my competition and demo vehicles, they provide all the angle and grip we love along with the strength and durability we need to compete with the best!"
Toyota 86 Drift
"I wouldn't have half the results! Only by running Wisefab in my Toyota 86 it just makes the car handle so good and let's me adjust set up pretty easy which is a massive help going from track to track!"