BMW E46 E46M Front Drift Angle Lock Kit V2
$1,790.00
excluding VAT
In stock
SKU
WF460
The V2 kit now offers the ability to adjust the ackermann angle (from the knuckle add-on) and also the caster (from the top mount). These new features make adjustment convenient and handy.
NB! The V2 kit is suitable for both standard models and M3.
Want to know how does Wisefab Lock kit fits your driftcar check below the link CHECK FITMENT or here!
For the rear we are offering the full solution as well including the unique design trailing arms, lower links and V2 upper links
Scroll down to order your spare parts conviently right here!
Here is our recommended alignment parameters:
Camber: E36 -6°; E46 -4°
Caster: E36 5°; E46 6°
Toe: if ackerman is 0 or negative then toe is 2 mm,
if ackerman is positive then toe is 0.
We found other products you might need!
- Higher roll center
Wisefab suspension kit brings the front roll center up on lowered cars, providing higher roll stiffness. - Revised steering geometry (trail and Ackermann)
You could tune your steering geometry from the positive to parallel Ackermann in just a few minutes even at trackside without messing up an alignment. - Good camber control with high steering angles
With high steering angles the leading wheel will have a positive camber, which is not a positive effect. It reduces the front grip and during turn or flip it creates a contact patch transition from inside edge to outside edge. It is not possible to eliminate it, but with our geometry it has decreased as much as possible. - Steering jacking control
During drifting, when steering angle is much bigger, jacking is also bigger, even with the same geometry and it could become a problem. We have monitored it and changed the geometry that it doesn’t cause any handling issues. - Predictable self-alignment control
With certain suspension geometry at high steering angles it could happen that the steering wheel is locking up at the end and driver needs to apply some force to flip it to other side. We know what causes it and have decreased it to minimum, if not eliminated it. - Adjustable lock-stopper.
- Stronger inner ball joint design over OEM and older Wisefab version.
Kit includes:
- Adjustable coilover upper mounts, Formula Drift compliance.
- Hub add-ons with Ackermann adjustment hardware.
- Lightweight lower control arms.
- Assembeled tie rods.
- Adjustable lower control arm rear mount.
- Installation guide
Other components, packaging and clearance.
- This kit assumes coilovers to have enough clearance.
- We recommend tire diameter not bigger than 645mm (235/40 R18).
- Wider fenders or fender flares needed with this kit.
| Make | BMW |
|---|---|
| Field | Drift |
| Placement | Front |
| Prodmaster Name | Drift Angle Lock Kit V2 |
Spare parts
All
Complete parts
Left Knuckle Add-on V2
Right Knuckle Add-on V2
Left Lower Control Arm
Right Lower Control Arm_
Tierod Assembly
Top Mount
Lower Control Arm Mount V2
Complete parts
Complete parts
2
Lower Control Arm
2
Lower Control Arm_
3
Tierod Assembly
4
Top Mount
5
Lower Control Arm Mount V2
Left Knuckle Add-on V2
Left Knuckle Add-on V2
2
BMW E36 Front Lower Control Arm Fixing Stud
3
Nut Nylock M12x1.5 RH 8.8 ZN DIN985-8
4
Washer Flat M12 ZN DIN125
5
Conical Bolt D16.4 L63
6
BMW E36M Front Knuckle Add-on V2 Spacer
7
BMW E36 Front Tie Rod Fixing V2
8
Conical Bolt D16.5 L65
9
BMW E36 Front Knuckle Add-on V2 ACK0 Washer
10
BMW E36 Front Knuckle Add-on V2 ACK3 Washer
11
Pin Spring 6x10 Normal ST DIN1481
12
BMW E36 Front Knuckle Add-on V2 Spacer
13
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
14
Conical Bolt D18 L63
15
Nut Hex Flange Lock M12x1.5 RH 10.9 ZF
Right Knuckle Add-on V2
Right Knuckle Add-on V2
2
BMW E36 Front Lower Control Arm Fixing Stud
3
Nut Nylock M12x1.5 RH 8.8 ZN DIN985-8
4
Washer Flat M12 ZN DIN125
5
Conical Bolt D16.4 L63
6
BMW E36M Front Knuckle Add-on V2 Spacer
7
BMW E36 Front Tie Rod Fixing V2
8
Conical Bolt D16.5 L65
9
BMW E36 Front Knuckle Add-on V2 ACK0 Washer
10
BMW E36 Front Knuckle Add-on V2 ACK3 Washer
11
Pin Spring 6x10 Normal ST DIN1481
12
BMW E36 Front Knuckle Add-on V2 Spacer
13
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
14
Conical Bolt D18 L63
15
Nut Hex Flange Lock M12x1.5 RH 10.9 ZF
Left Lower Control Arm
Left Lower Control Arm
2
Bolt Allen M12x1.50x 12.5 RH 12.9 ZN
3
BushingT ID 10 OD27 h33 Excentric Lock Stopper
4
Bolt Allen M10x1.5x 55 RH 8.8 ZN DIN 912
5
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
6
Spacer ID12 OD16 h10 SPC
7
C-Clip InternalSTD d32 ST DIN472
8
Spherical ID16/OD32
9
Spacer ID12 OD16 h7.5
10
Nut Nylock M14x1.5 RH 8.8 ZN DIN985-8
11
Control Arm Inner Joint Shaft V2
12
Spacer ID14 OD16 h10 SPC
13
Spacer ID14 OD16 h10
Right Lower Control Arm_
Right Lower Control Arm_
2
Bolt Allen M12x1.50x 12.5 RH 12.9 ZN
3
BushingT ID 10 OD27 h33 Excentric Lock Stopper
4
Bolt Allen M10x1.5x 55 RH 8.8 ZN DIN 912
5
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
6
Spacer ID12 OD16 h10 SPC
7
C-Clip InternalSTD d32 ST DIN472
8
Spherical ID16/OD32
9
Spacer ID12 OD16 h7.5
10
Nut Nylock M14x1.5 RH 8.8 ZN DIN985-8
11
Control Arm Inner Joint Shaft V2
12
Spacer ID14 OD16 h10 SPC
13
Spacer ID14 OD16 h10
Tierod Assembly
Tierod Assembly
2
Tie Rod Extension
3
Rod end 14x1.5 RH female CrMo
4
Spacer ID10 OD14 h 5.4
Top Mount
Top Mount
2
Spherical ID18/OD35
3
C-Clip InternalSTD d35 ST DIN472
5
Nut Hex Flange M 8x1.25 RH 8.8 ZN
Lower Control Arm Mount V2
Lower Control Arm Mount V2
2
Rod end 20x1.5 RH male CrMo
3
BMW E46 Front Right Control Arm Mount V2 Spacer
4
Bolt Allen M10x1.5x 40 RH 10.9 ZN DIN 912
"’We started working together with Wisefab back in 2014 when we launched our Falken Tyres Nissan 240sx for European competition. Since then, we have enjoyed working closely with the engineers at Wisefab testing new products before going into production and have had a lot of success winning multiple championship worldwide. Thank you to everyone at Wisefab for believing in us and producing such top-quality products."
“When I first installed a Wisefab lock kit it truly opened the door for some more aggressive driving style. I quickly began to expect nothing less than the massive angle and performance that Wisefab provides and installed a lock kit on all (4) of my Nissan 240sx that I currently drift. Also, after testing what I though was a very competitive rear suspension solution against the latest Wisefab rear kit, I was blown away with the apparent grip gain the rear Wisefab kit yielded. I am so thankful that Wisefab has poured so much effort into creating a bolt on suspension solution that transforms a Nissan 240sx into what I believe is still the most competitive drift chassis in the world."
"I love the Wisefab suspension kits used on my competition and demo vehicles, they provide all the angle and grip we love along with the strength and durability we need to compete with the best!"
"I wouldn't have half the results! Only by running Wisefab in my Toyota 86 it just makes the car handle so good and let's me adjust set up pretty easy which is a massive help going from track to track!"
