Nissan S13 Front V2 Drift Angle Lock Kit with Rack Offset Spacers
$2,100.00
excluding VAT
In stock
SKU
WF130 OFF
Wisefab S13 Nissan angle kit with rack offset spacers has two major upgrades. Lower control arm has been redesigned for more convenient alignment setup. The knuckle has been designed to allow more suspension travel with the trending long stroke coilovers. The result was more grip at the front and more precise steering. This will give you the competitive edge. All the parts in the Nissan S13 angle kit are provided as spare parts.
S13 kit is for the 4 lug spindle, if you have 5 lug on your S13 please select the Nissan S14 Angle kit.
Want to know how does Wisefab Lock kit fits your driftcar check below the link CHECK FITMENT or here!
Scroll down to order your spare parts conviently right here!
Here is our recommended alignment parameters: Toe in/out: If Ackermann is 0 or negative then toe is 2mm out. If Ackermann is positive then toe is 0 Camber: -4 +/-0,5 Caster: 3,5 +/-0,5
More usable lock. 65+ degrees of lock, better feel and precise handling. You could tune your steering geometry either towards positive or negative Ackermann in just a few minutes even at trackside without messing up an alignment. Ackermann adjustment kit included.
Less sensitive steering. Increased steering ratio for smooth handling.
More suspension travel. Less interference risk at full droop. Longstroke coilover kits can be used.
Lighter and stronger. Optimized design in combination with high strenght steel is used.
Higher roll center (RC). On Wisefab knuckle, the ball joint is lowered 60mm, which brings the front RC up on lowered car, providing higher roll stiffness and letting to remove the front anti roll bar (sway bar) that is quite difficult to package with that high lock angles.
Adjustable camber and caster with adjustable doubleplates.
Adjustable lock stopper.
One piece lower control arm desing. Lower links are replaced with one arm. Drifting with higher steering angle the stiffness and packaging would become an issue. Therefore lower one piece arm is used.
Very good camber control and minimal bump steer with high steering angles. On drift cars the dynamic camber and bump steer is much more important than static. With our kinematics we have assured that the camber would provide very good front grip and bump steer is minimal at all the range of steering.
Steering jacking control. During drifting, when steering angle is much bigger, jacking is also bigger, even with the same geometry and it could become a problem. We have changed the geometry that it doesn’t cause any handling issues.
Consistent and predictable self-alignment torque. Caster is not the only important parameter to provide sufficient self-alignment torque especially at high lock. It’s the combination of different parameters to maintain consistent trail and self-alignment torque. With our setup the steering wheel turns always to the direction of movement and doesn’t get stuck at full lock.
Kit includes:
Adjustable coilover upper mounts, Formula Drift compliance.
Knuckles with hardware.
Lower control arms.
Assembeled tie rods.
Rack offset kit.
Rack installation guide.
Installation guide.
Other components, packaging and clearance.
This kit assumes coilovers to have enough clearance.
Dependent on rim width and ET, wider fenders or fender flares would be needed.
With tire diameter up to 635mm (215/45R17, 225/45R17, 235/40R17, 225/40R18 etc) and lowered ride height the inner wheel wells need to be slightly modified.
Recommended backspacing is 135-140mm (7“ ET45; 8“ ET35; 9“ ET25).If ET is smaller, then wheels stay more outwards, if ET is bigger, then spacers need to be used.
This calculator is fixed with the values specific to this particular product, car make and model. Full fitment calculator can be accessed here
Fender Arch Height from Ground (mm)
Tire Width
Tire Height or Diameter
Rim Diameter
Rim Width
ET
Wheelspacer (mm)
Suspension selection
Suspension selection
OEM
WISEFAB
CUSTOM
1689 mm
1689 mm
Fender to Fender
1537 mm
1703 mm
Hub to Hub
-1 °
-4 °
Camber
7 °
4 °
Caster
-1 mm
-2 mm
Toe
Set your desired rim and tire parameters in our fitment calculator to have a better overview how Wisefab will transform your driftcar. Fender arch height is your indicator on ride height. Check the fitment and learn about missing fender gap before ordering widebody kit. In the custom section you can edit the fender to fender and wheelhub to wheelhub measurments according to your driftcar. Use the max width to check if your car will fit on your trailer. Have fun with this fitment calculator.
"’We started working together with Wisefab back in 2014 when we launched our Falken Tyres Nissan 240sx for European competition. Since then, we have enjoyed working closely with the engineers at Wisefab testing new products before going into production and have had a lot of success winning multiple championship worldwide. Thank you to everyone at Wisefab for believing in us and producing such top-quality products."
“When I first installed a Wisefab lock kit it truly opened the door for some more aggressive driving style. I quickly began to expect nothing less than the massive angle and performance that Wisefab provides and installed a lock kit on all (4) of my Nissan 240sx that I currently drift. Also, after testing what I though was a very competitive rear suspension solution against the latest Wisefab rear kit, I was blown away with the apparent grip gain the rear Wisefab kit yielded. I am so thankful that Wisefab has poured so much effort into creating a bolt on suspension solution that transforms a Nissan 240sx into what I believe is still the most competitive drift chassis in the world."
"I love the Wisefab suspension kits used on my competition and demo vehicles, they provide all the angle and grip we love along with the strength and durability we need to compete with the best!"
"I wouldn't have half the results! Only by running Wisefab in my Toyota 86 it just makes the car handle so good and let's me adjust set up pretty easy which is a massive help going from track to track!"
