Toyota Supra A90 Rear Suspension Drop Knuckle Kit
$2,650.00
excluding VAT
In stock
SKU
WFA91
The Toyota Supra A90 is one of the most discussed new cars around. Rear wheel drive together with turbocharged in-line six engine offers great potential for drifting. Here at Wisefab we have developed PRO level rear suspension kit for this chassis. It allows to gain more grip ans stability over the OEM setup. This kit has been tested in Japan and USA by the best drivers around and we are happy to offer this product now to our customers.
All the metal components on Wisefab A90 front suspension are from high strength steel, including sheet metal components, tubes, tube ends and rod end housings. Rod ends and spherical bearings are used, no rubber bushings.
Want to know how does Wisefab Lock kit fits your driftcar check below the link CHECK FITMENT or here!
Check out the 2020 Toyota Supra Lock kit!
Scroll down to order your spare parts conviently right here!
- Revised kinematics, not just dropped knuckle.
If the focus is more towards performance, then the car can act better with lowered ride height, but then the factory designed kinematics wouldn't work as it supposed to. The kit would give a good kinematics with lowered car - higher roll center, , revised cambergain, anti-squat and bumpsteer for maximum grip. - Easy camber adjustment.
As the top links are straight tubular type, then camber can be adjusted simply by changing their length. - Bump steer adjustment.
Possibility to adjust bump steer by changing rod end location in a slot. - Anti-squat adjustment possibility.
Possibility to adjust anti-squat by changing the top forward link height on upright. It can be done in less than 10 minutes at the trackside. Lowering link would increase anti-squat, raising it would decrease anti-squat. - Original wheelspeed sensor (ABS sensor) can be used.
- Only takes either M model or 336mm or bigger brake discs.
Smaller brakes will not fit. - Wheel bearing size should be 45x85x41
Kit includes:
- Pre-set suspension links.
- Uprights with hardware.
- Subframe bushings with sperical bearings.
Component fitment
- Wheel bearing: OEM rear wheel bearing can not be used, it has to be sourced from BMW E90. Only the bigger size wheel bearing can be used 45x85x41. Part number 33416775842.
- Wheel hub: Wheel hub has to be sourced from BMW E90 and shoulde be for the bigger wheel bearing. Part number 33416760058.
- Wheels: Wheel hub has 5x120 PCD. This means that OEM wheels can not be used.
- Brakes: Brakes has to be from BMW E90 with 336 mm brake disc or BMW E90 M3. OEM brakes do not fit.
- Strut: OEM fitment ride hight adjustable coilovers must be used.
- Driveshaft has to be from BMW E90 or E90 M3 or an aftermarket one that fits E90
| Make | Toyota |
|---|---|
| Field | Drift |
| Placement | Rear |
| Prodmaster Name | Suspension Drop Knuckle Kit |
Spare parts
All
Complete parts
Left Knuckle
Right Knuckle
Suspension Arm #2
Suspension Arm #3
Suspension Arm #4
Suspension Arm #6
Suspension Mod Arm #7
Complete parts
Complete parts
2
Suspension Arm #2
3
Suspension Arm #3
4
Suspension Arm #4
5
Suspension Arm #6
6
Suspension Mod Arm #7
Left Knuckle
Left Knuckle
2
Bolt Hex M10x1.5x 35 RH 10.9 ST DIN 933
3
Bolt Hex M12x1.5x 80 RH 10.9 ST DIN 960
4
Washer Flat M12 ZN DIN125
5
Nut Nylock M12x1.5 RH 8.8 ZN DIN985-8
6
Bolt Hex M10x1.5x 60 RH 10.9 ST DIN 931
7
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
8
Washer Flat M10 ZN DIN125
9
Bolt Hex M10x1.5x 55 RH 10.9 ST DIN 931
11
Bolt Hex M10x1.5x 45 RH 10.9 ST DIN 931
13
Brake Adapter
14
Pin Spring 6x10 Normal ST DIN1481
15
Nut Nylock M 8x1.25 RH 8.8 ZN DIN985-8
16
Washer Flat M 8 ZN DIN125
17
Bolt Hex M 8x1.25x 45 RH 8.8 ZN DIN 931
Right Knuckle
Right Knuckle
2
Bolt Hex M10x1.5x 35 RH 10.9 ST DIN 933
3
Bolt Hex M12x1.5x 80 RH 10.9 ST DIN 960
4
Washer Flat M12 ZN DIN125
5
Nut Nylock M12x1.5 RH 8.8 ZN DIN985-8
6
Bolt Hex M10x1.5x 60 RH 10.9 ST DIN 931
7
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
8
Washer Flat M10 ZN DIN125
9
Bolt Hex M10x1.5x 55 RH 10.9 ST DIN 931
11
Bolt Hex M10x1.5x 45 RH 10.9 ST DIN 931
13
Brake Adapter
14
Pin Spring 6x10 Normal ST DIN1481
15
Nut Nylock M 8x1.25 RH 8.8 ZN DIN985-8
16
Washer Flat M 8 ZN DIN125
17
Bolt Hex M 8x1.25x 45 RH 8.8 ZN DIN 931
Suspension Arm #2
Suspension Arm #2
2
Rod end 16x1.5 RH male CrMo
3
Spacer ID12 OD16 h22
4
Double Adjuster Female/Male M16x1.5 M22x1.5
5
Bolt Hex M 8x1.25x 25 RH 12.9 ST DIN 933
6
Bolt Hex M12x1.5x 90 RH 10.9 ST DIN 960
7
Washer Flat M12 ZN DIN125
8
Nut Nylock M12x1.5 RH 8.8 ZN DIN985-8
9
Spacer ID12 OD16 h18
10
Spherical ID16/OD32
11
C-Clip InternalSTD d32 ST DIN472
Suspension Arm #3
Suspension Arm #3
2
Spacer ID12 OD14 h14
3
Rod end 14x1.5 LH male CrMo
4
Nut Thin M14x1.5 LH 8.8 ZN DIN936/439
5
Nut Thin M12x1.5 RH 8.8 ZN DIN936/439
6
Spacer ID10 OD12 h14
7
Rod end 12x1.5 RH male CrMo
Suspension Arm #4
Suspension Arm #4
2
Spacer ID12 OD14 h14
3
Rod end 14x1.5 LH male CrMo
4
Nut Thin M14x1.5 LH 8.8 ZN DIN936/439
5
Nut Thin M12x1.5 RH 8.8 ZN DIN936/439
6
Spacer ID10 OD12 h 7
7
Rod end 12x1.5 RH male CrMo
Suspension Arm #6
Suspension Arm #6
2
Spacer ID12 OD16 h13.5
3
Rod end 16x1.5 RH male CrMo
4
Double Adjuster Female/Male M16x1.5 M22x1.5
5
Bolt Hex M 8x1.25x 25 RH 12.9 ST DIN 933
6
C-Clip InternalSTD d26 ST DIN472
7
Spacer ID10 OD12 h14
8
Spherical ID12/OD26
Suspension Mod Arm #7
Suspension Mod Arm #7
2
Spacer ID10 OD14 h11
3
Rod end 14x1.5 LH male CrMo
4
Nut Thin M14x1.5 LH 8.8 ZN DIN936/439
5
Nut Thin M12x1.5 RH 8.8 ZN DIN936/439
6
Rod end 12x1.5 RH male CrMo
7
Spacer ID10 OD12 h 7
"’We started working together with Wisefab back in 2014 when we launched our Falken Tyres Nissan 240sx for European competition. Since then, we have enjoyed working closely with the engineers at Wisefab testing new products before going into production and have had a lot of success winning multiple championship worldwide. Thank you to everyone at Wisefab for believing in us and producing such top-quality products."
“When I first installed a Wisefab lock kit it truly opened the door for some more aggressive driving style. I quickly began to expect nothing less than the massive angle and performance that Wisefab provides and installed a lock kit on all (4) of my Nissan 240sx that I currently drift. Also, after testing what I though was a very competitive rear suspension solution against the latest Wisefab rear kit, I was blown away with the apparent grip gain the rear Wisefab kit yielded. I am so thankful that Wisefab has poured so much effort into creating a bolt on suspension solution that transforms a Nissan 240sx into what I believe is still the most competitive drift chassis in the world."
"I love the Wisefab suspension kits used on my competition and demo vehicles, they provide all the angle and grip we love along with the strength and durability we need to compete with the best!"
"I wouldn't have half the results! Only by running Wisefab in my Toyota 86 it just makes the car handle so good and let's me adjust set up pretty easy which is a massive help going from track to track!"
