Subaru BRZ Front Lock Kit for Lexus IS Rear Rack

$3,500.00
excluding VAT
In stock
SKU
WF8602
or View Spares

The original location of the steering rack on the Subaru BRZ, which is equipped with a boxer engine, is not very suitable for drifting. To address this issue, the steering rack has been relocated from under the front cross-member, allowing for the use of various engines, including the boxer, I6/V8, and others. To use the kit, a Lexus IS 1st generation (XE10 1998-2005) hydraulic steering rack is required. The kit includes the steering rack attachment/cross-member insert and cross-member supports, but a modification of the cross-member through DIY cutting and welding is necessary.

Want to know how does Wisefab Subaru BRZ Lock kit fit your drift car check the link CHECK FITMENT below or here!

Check out the Subaru BRZ Rear Suspension kit

Scroll down to order the spare parts for your Subaru BRZ front lock kit conveniently right here!

Here is our recommended alignment parameters:
Toe in/out: If Ackermann is 0 or negative then toe is 2mm out. If Ackermann is positive then toe is 0
Camber: -6+/-0,5

Caster: 5,5 +/-0,5

  • 62 degrees of lock, parallel steering
    You can tune your steering geometry towards positive Ackermann in just a few minutes even at trackside without messing up the alignment. Ackermann adjustment is included in the kit.
  • 7 kg of weight reduction
    While still maintaining the required strength and stiffness.
  • 7075-T6 aluminium
    Billet CNC knuckles and arms with optimized design and all double shear connections provide low weight and high strenght.
  • CrMo rod ends and sphericals used instead of OEM bushings
  • Higher roll center (RC)
    With our knuckle, the ball joint is lowered, which brings the front RC up on a lowered car, providing higher roll stiffness. This allows to remove the front anti roll-bar (sway bar) that is quite difficult to package with high lock angles.
  • Good camber control and minimal bump steer with high steering angles
    On drift cars the dynamic camber and bump steer is much more important than static. With our kinematics we have assured that the camber will provide very good front grip and bump steer is minimal throughout the steering range.
  • Steering jacking control
    During drifting, when steering angle is increased, jacking is also bigger, even with the same geometry it could become a problem. We have changed the geometry in a way that doesn't cause any handling issues.
  • Consistent and predictable self-alignment torque. 
    Caster is not the only important parameter to provide sufficient self-alignment torque, especially at high lock. It's the combination of different parameters to maintain consistent trail and self-alignment torque. With our setup the steering wheel turns always to the direction of movement and doesn't get stuck at full lock.

Kit includes:

  • Pre-set lower control arms
  • Knuckles with hardware
  • Assembeled tie rods
  • Pre-set coilover upper mounts
  • Rack relocating kit
  • Crossmember supports
  • Installation guide

 

Other information:

  • This kit assumes coilovers for enough clearance
  • Dependent on rim width and ET, wider fenders or fender flares are needed.
  • Due to extremely wide engine bay on Subaru BRZ, we recommend using tires no bigger than 605mm (215/40R17, 225/40R17, 215/35R18, 225/35R18)
  • With tire diameter up to 635mm (215/45R17, 225/45R17, 235/40R17, 225/40R18 etc) and lowered ride height the inner wheel wells need to be slightly modified.
  • Minimum rim size is 17“, but we recommend using 18“
  • Recommended backspacing is 135-140mm (7“ ET45; 8“ ET35; 9“ ET25). If ET is smaller, then wheels stay more outwards, if ET is bigger, then spacers need to be used.
  • Original wheel speed sensor can be used
More Information
Make Subaru
Field Drift
Placement Front
Prodmaster Name Lock Kit for Lexus IS Rear Rack
Wisefab fitment calculator
Make and Model
?
Fender Arch Height from Ground (mm)
Tire Width
Tire Height or Diameter
Rim Diameter
Rim Width
ET
Wheelspacer (mm)
Suspension selection
Suspension selection
OEM
WISEFAB
CUSTOM
 
1772 mm
1772 mm
Fender to Fender
1548 mm
1695 mm
Hub to Hub
-1 °
-6 °
Camber
5 °
5 °
Caster
0 mm
-2 mm
Toe

Set your desired rim and tire parameters in our fitment calculator to have a better overview how Wisefab will transform your driftcar. Fender arch height is your indicator on ride height. Check the fitment and learn about missing fender gap before ordering widebody kit. In the custom section you can edit the fender to fender and wheelhub to wheelhub measurments according to your driftcar. Use the max width to check if your car will fit on your trailer. Have fun with this fitment calculator.

Spare parts

All
Complete parts
Left Knuckle
Right Knuckle
Left Lower Control Arm
Right Lower Control Arm
Tie Rod Assembly
Left Top Mount
Right Top Mount
Left Subframe Support
Right Subframe Support
GT86 IS Rack Insert Assembly
GT86 Subframe Jig Half

Complete parts

Complete parts

1
Knuckle
Left
WF860_100LA
$860.00
excluding VAT
Right
WF860_100RA
$860.00
excluding VAT
2
Lower Control Arm
Left
WF860_200LA
$590.00
excluding VAT
Right
WF860_200RA
$590.00
excluding VAT
3
Tie Rod Assembly
WF080_600A
$105.00
excluding VAT
4
Top Mount
Left
WF860_500LA
$170.00
excluding VAT
Right
WF860_500RA
$170.00
excluding VAT
5
Subframe Support
Left
WF860_400L
$80.00
excluding VAT
Right
WF860_400R
$80.00
excluding VAT
6
GT86 IS Rack Insert Assembly
WF860_840A
$395.00
excluding VAT
7
GT86 Subframe Jig Half
WF860_850A
$29.00
excluding VAT

Left Knuckle

Left Knuckle

2
Bolt Hex M10x1.5x130 RH 10.9 ST DIN 931
B01110150130R3SD931
$9.40
excluding VAT
3
Ackermann Washer Cross 0 Offset
WF860_140
$11.00
excluding VAT
4
Ackermann Washer Cross 1.5 Offset
WF860_141
$11.00
excluding VAT
5
Ackermann Washer Cross 3 Offset
WF860_142
$11.00
excluding VAT
6
Ackermann Washer Cross 4.5 Offset
WF860_143
$11.00
excluding VAT
7
BushingT ID10 OD32 h50 Special
WF860_901
$18.00
excluding VAT
8
Washer Flat M10 ZN DIN125
B03110NAZD125
$2.30
excluding VAT
9
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$2.30
excluding VAT
10
Bolt Hex M12x1.5x 70 RH 10.9 ST DIN 960
B01112150070R3SD960
$9.40
excluding VAT
11
Washer Flat M12 ZN DIN125
B03112NAZD125
$2.30
excluding VAT
12
Bolt Hex M 8x1.25x 70 RH 8.8 ZN DIN 931
B01108125070R2ZD931
$2.30
excluding VAT
13
Washer Flat M 8 ZN DIN125
B03108NAZD125
$2.30
excluding VAT
14
BushingT ID 8 OD16 h41
WF013_910
$13.00
excluding VAT
15
Nut Nylock M 8x1.25 RH 8.8 ZN DIN985-8
B02208125R2ZD9858
$2.30
excluding VAT

Right Knuckle

Right Knuckle

2
Bolt Hex M10x1.5x130 RH 10.9 ST DIN 931
B01110150130R3SD931
$9.40
excluding VAT
3
Ackermann Washer Cross 0 Offset
WF860_140
$11.00
excluding VAT
4
Ackermann Washer Cross 1.5 Offset
WF860_141
$11.00
excluding VAT
5
Ackermann Washer Cross 3 Offset
WF860_142
$11.00
excluding VAT
6
Ackermann Washer Cross 4.5 Offset
WF860_143
$11.00
excluding VAT
7
BushingT ID10 OD32 h50 Special
WF860_901
$18.00
excluding VAT
8
Washer Flat M10 ZN DIN125
B03110NAZD125
$2.30
excluding VAT
9
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$2.30
excluding VAT
10
Bolt Hex M12x1.5x 70 RH 10.9 ST DIN 960
B01112150070R3SD960
$9.40
excluding VAT
11
Washer Flat M12 ZN DIN125
B03112NAZD125
$2.30
excluding VAT
12
Bolt Hex M 8x1.25x 70 RH 8.8 ZN DIN 931
B01108125070R2ZD931
$2.30
excluding VAT
13
Washer Flat M 8 ZN DIN125
B03108NAZD125
$2.30
excluding VAT
14
BushingT ID 8 OD16 h41
WF013_910
$13.00
excluding VAT
15
Nut Nylock M 8x1.25 RH 8.8 ZN DIN985-8
B02208125R2ZD9858
$2.30
excluding VAT

Left Lower Control Arm

Left Lower Control Arm

2
Spacer ID12 OD16 h18
WF136_903
$13.00
excluding VAT
3
Rod end 16x1.5 RH male CrMo
SRODEND16X1.5 RH M
$39.00
excluding VAT
4
Nut Thin M16x1.5 RH 8.8 ZN DIN936/439
B02316150R2ZD936/439
$4.30
excluding VAT
5
Bolt Hex M14x1.5x100 RH 10.9 ST DIN 960
B01114150100R3SD960
$13.00
excluding VAT
6
Washer Flat M14 ZN DIN125
B03114NAZD125
$2.30
excluding VAT
7
Spacer ID14 OD16 h10
WF036_903
$13.00
excluding VAT
8
Spacer ID14 OD16 h29
WF860_902
$13.00
excluding VAT
9
Spacer ID12 OD16 h10
WF013_903
$13.00
excluding VAT
10
Spherical ID16/OD32
SSPHERICAL 16/32
$38.00
excluding VAT
11
C-Clip InternalSTD d32 ST DIN472
B04132SD472
$2.30
excluding VAT

Right Lower Control Arm

Right Lower Control Arm

2
Spacer ID12 OD16 h18
WF136_903
$13.00
excluding VAT
3
Rod end 16x1.5 RH male CrMo
SRODEND16X1.5 RH M
$39.00
excluding VAT
4
Nut Thin M16x1.5 RH 8.8 ZN DIN936/439
B02316150R2ZD936/439
$4.30
excluding VAT
5
Bolt Hex M14x1.5x100 RH 10.9 ST DIN 960
B01114150100R3SD960
$13.00
excluding VAT
6
Washer Flat M14 ZN DIN125
B03114NAZD125
$2.30
excluding VAT
7
Spacer ID14 OD16 h10
WF036_903
$13.00
excluding VAT
8
Spacer ID14 OD16 h29
WF860_902
$13.00
excluding VAT
9
Spacer ID12 OD16 h10
WF013_903
$13.00
excluding VAT
10
Spherical ID16/OD32
SSPHERICAL 16/32
$38.00
excluding VAT
11
C-Clip InternalSTD d32 ST DIN472
B04132SD472
$2.30
excluding VAT

Tie Rod Assembly

Tie Rod Assembly

2
Tie Rod Inner M14x1.5 M14x1.5 L366
STIEROD_M14_M14_L366
$31.00
excluding VAT
3
Spacer ID10 OD14 h 5.4
WF080_921
$11.00
excluding VAT
4
Rod end 14x1.5 RH female CrMo
SRODEND14X1.5 RH F
$39.00
excluding VAT

Left Top Mount

Left Top Mount

2
Camber Plate Spherical Housing REG
WF013_917A
$80.00
excluding VAT
3
Bolt Hex M 8x1.25x 16 RH 8.8 ZN DIN 933
B01108125016R2ZD933
$2.30
excluding VAT
4
Bolt AllenFlat M 6x1.0x 16 RH 8.8 ZN DIN7991
B01306100016R2SD7991
$2.30
excluding VAT
5
Nut Hex Flange M 8x1.25 RH 8.8 ZN
B02508125R2ZD69238
$2.30
excluding VAT

Right Top Mount

Right Top Mount

2
Camber Plate Spherical Housing REG
WF013_917A
$80.00
excluding VAT
3
Bolt Hex M 8x1.25x 16 RH 8.8 ZN DIN 933
B01108125016R2ZD933
$2.30
excluding VAT
4
Bolt AllenFlat M 6x1.0x 16 RH 8.8 ZN DIN7991
B01306100016R2SD7991
$2.30
excluding VAT
5
Nut Hex Flange M 8x1.25 RH 8.8 ZN
B02508125R2ZD69238
$2.30
excluding VAT

GT86 IS Rack Insert Assembly

GT86 IS Rack Insert Assembly

2
IS Steering Rack Clamp 2
WF860_830
$48.00
excluding VAT
3
IS Steering Rack Clamp 1
WF860_820
$48.00
excluding VAT
4
BushingT ID9_OD29,5_h54 Special
WF860_909
$24.00
excluding VAT
5
BushingT ID9 OD25.6 h49.5 Step
WF860_907
$24.00
excluding VAT
6
BushingT ID25.8_OD36_h11.5
WF860_908
$9.40
excluding VAT
7
GT86 IS Rack Install JigL
WF860_811L
$24.00
excluding VAT
8
GT86 IS Rack Install JigR
WF860_811R
$24.00
excluding VAT
9
Washer Flat M 8 ZN DIN125
B03108NAZD125
$2.30
excluding VAT
10
Bolt Allen M 8x1.25x 16 RH 12.9 ST DIN 912
B01208125016R4SD912
$2.30
excluding VAT
11
Bolt Allen M 8x1.25x 70 RH 12.9 ST DIN 912
B01208125070R4SD912
$4.30
excluding VAT
12
Bolt Hex M14x1.5x 30 RH 10.9 ST DIN 960
B01114150030R3SD960
$6.40
excluding VAT
13
Washer Flat M12 ZN DIN125
B03112NAZD125
$2.30
excluding VAT
14
Bolt Hex M12x1.5x 80 RH 10.9 ST DIN 960
B01112150080R3SD960
$9.40
excluding VAT
15
Rack Extender M14x1.5 M14x1.5 L81
WF860_910
$35.00
excluding VAT
16
V2 Steering Column Extender Assembly
WF149_040A
$125.00
excluding VAT
17
Nut Thin M12x1.5 RH 8.8 ZN DIN936/439
B02312150R2ZD936/439
$4.30
excluding VAT
Wisefab Nissan 240sx
"’We started working together with Wisefab back in 2014 when we launched our Falken Tyres Nissan 240sx for European competition. Since then, we have enjoyed working closely with the engineers at Wisefab testing new products before going into production and have had a lot of success winning multiple championship worldwide. Thank you to everyone at Wisefab for believing in us and producing such top-quality products."
Nissan 240sx Drift
“When I first installed a Wisefab lock kit it truly opened the door for some more aggressive driving style. I quickly began to expect nothing less than the massive angle and performance that Wisefab provides and installed a lock kit on all (4) of my Nissan 240sx that I currently drift. Also, after testing what I though was a very competitive rear suspension solution against the latest Wisefab rear kit, I was blown away with the apparent grip gain the rear Wisefab kit yielded. I am so thankful that Wisefab has poured so much effort into creating a bolt on suspension solution that transforms a Nissan 240sx into what I believe is still the most competitive drift chassis in the world."
Nissan 240sx Lock kit
"I love the Wisefab suspension kits used on my competition and demo vehicles, they provide all the angle and grip we love along with the strength and durability we need to compete with the best!"
Toyota 86 Drift
"I wouldn't have half the results! Only by running Wisefab in my Toyota 86 it just makes the car handle so good and let's me adjust set up pretty easy which is a massive help going from track to track!"