Chevrolet Corvette C5 C6 Front Drift Angle Lock kit

$2,450.00
excluding VAT
In stock
SKU
WFC60
or View Spares

The Corvette C5 / C6 chassis have become increasingly popular in drifting. This real-deal sports car is very capable out of the box and has a lot of potential as a drift car.

The Wisefab PRO level drift angle kit includes everything you need to get the best possible drift features and achieve a 65+ degree steering angle. Knuckle kinematics have been improved in several ways and an Ackermann angle adjustment has been added. Control arms are extended and conveniently adjustable for quick alignment.

When using this kit, you can benefit from optional "C6 Rack Offset Spacer Kit" that will allow you to achieve even bigger steering angle on C6 chassis (not needed on C5) and improves the Ackermann curve.

Recommended alignment parameters:
Toe in/out: If Ackermann is 0 or negative then toe is 2mm out. If Ackermann is positive, then toe is 0
Camber: -3.5
Caster: 6

▼Click the link below for all the details and unique features▼

 

 

  • 65+ degrees of steering angle, parallel steering, adjustable lock-stopper. You can tune your steering geometry either towards positive or negative Ackermann in just a few minutes even at trackside without messing up an alignment. Ackermann adjustment kit is included.
  • Easily adjustable one-piece lower control arm desing. Our "double adjuster" allows you to easyly and quickly fine tune your setup.
  • Higher roll center (RC).
    On Wisefab knuckles, joints are slightly dropped, which brings the front RC up on lowered car, providing higher roll stiffness and improves drivability.
  • Very good camber control and minimal bump steer with high steering angle.
    On drift cars the dynamic camber and bump steer is much more important than static. With our kinematics we have assured that the camber would provide very good front grip and bump steer is minimal at all the range of steering.
  • Steering jacking control.
    During drifting, when steering angle is much bigger, jacking is also bigger, even with the same geometry and it could become a problem. We have changed the geometry so that it helps to prevent any handling issues.
  • Consistent and predictable self-alignment torque.
    Caster is not the only important parameter to provide sufficient self-alignment torque especially at high angle. It’s the combination of different parameters to maintain consistent trail and self-alignment torque. With our setup the steering wheel turns always to the direction of movement and doesn’t get stuck at full lock. 
  • Original wheelspeed sensor (ABS sensor) can be used.

Kit includes

  • Knuckles with hardware
  • Lower control arms
  • Upper control arms
  • Assembeled tie rods
  • Installation guide

Useful information

Wheel Backspacing (max):

  • 17" wheel - 145 mm
  • 18" wheel - 147 mm
  • 19" wheel - 150 mm

Coilover length:

  • Rideheight 378 mm
  • Maximum: 430 mm
  • Minimum 345 mm

 

More Information
Make Chevrolet
Field Drift
Placement Front
Prodmaster Name Drift Angle Lock kit
Wisefab fitment calculator
Make and Model
?
Fender Arch Height from Ground (mm)
Tire Width
Tire Height or Diameter
Rim Diameter
Rim Width
ET
Wheelspacer (mm)
Suspension selection
Suspension selection
OEM
WISEFAB
CUSTOM
 
1820 mm
1820 mm
Fender to Fender
1672 mm
1827 mm
Hub to Hub
0 °
-3 °
Camber
7 °
6 °
Caster
0 mm
-2 mm
Toe

Set your desired rim and tire parameters in our fitment calculator to have a better overview how Wisefab will transform your driftcar. Fender arch height is your indicator on ride height. Check the fitment and learn about missing fender gap before ordering widebody kit. In the custom section you can edit the fender to fender and wheelhub to wheelhub measurments according to your driftcar. Use the max width to check if your car will fit on your trailer. Have fun with this fitment calculator.

Spare parts

All
Complete parts
Left Knuckle
Right Knuckle
Left Lower Control Arm
Right Lower Control Arm
Upper Control Arm
Tie Rod Assembly

Complete parts

Complete parts

1
Knuckle
Left
WFC60_100LA
$650.00
excluding VAT
Right
WFC60_100RA
$650.00
excluding VAT
2
Lower Control Arm
Left
WFC60_200LA
$510.00
excluding VAT
Right
WFC60_200RA
$510.00
excluding VAT
3
Upper Control Arm
WFC60_300A
$300.00
excluding VAT
4
Tie Rod Assembly
WFC60_600A
$60.00
excluding VAT

Left Knuckle

Left Knuckle

1
Knuckle
Left
WFC60_100LA
$650.00
excluding VAT
2
Spherical ID16/OD32
SSPHERICAL 16/32
$35.00
excluding VAT
3
C-Clip InternalSTD d32 ST DIN472
B04132SD472
$2.10
excluding VAT
4
BushingT ID 8 OD22 h51 Excentric Lock Stopper
WF370_950
$16.00
excluding VAT
5
Bolt Hex M 8x1.25x 70 RH 8.8 ZN DIN 931
B01108125070R2ZD931
$2.10
excluding VAT
6
Bolt Hex M12x1.5x 80 RH 10.9 ST DIN 960
B01112150080R3SD960
$8.90
excluding VAT
7
Washer FlatSmall M12 ZN DIN433
B03212NAZD433
$2.10
excluding VAT
8
Nut Nylock M12x1.5 RH 8.8 ZN DIN985-8
B02212150R2ZD9858
$2.10
excluding VAT
9
Ackermann Washer Round 0 offset
WF013_140
$10.00
excluding VAT
10
Ackermann Washer Round 3 Offset
WF080_142
$10.00
excluding VAT
11
Ackermann Washer Round 6 Offset
WF080_144
$10.00
excluding VAT
12
Bolt Hex M10x1.5x 70 RH 10.9 ST DIN 931
B01110150070R3SD931
$4.00
excluding VAT
13
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$2.10
excluding VAT
14
Rod end 14x1.5 RH female CrMo
SRODEND14X1.5 RH F
$36.00
excluding VAT
15
Spacer ID10 OD14 h13
WF370_909
$12.00
excluding VAT
16
Spacer ID10 OD14 h 9
WF861_903
$10.00
excluding VAT

Right Knuckle

Right Knuckle

1
Knuckle
Right
WFC60_100RA
$650.00
excluding VAT
2
Spherical ID16/OD32
SSPHERICAL 16/32
$35.00
excluding VAT
3
C-Clip InternalSTD d32 ST DIN472
B04132SD472
$2.10
excluding VAT
4
BushingT ID 8 OD22 h51 Excentric Lock Stopper
WF370_950
$16.00
excluding VAT
5
Bolt Hex M 8x1.25x 70 RH 8.8 ZN DIN 931
B01108125070R2ZD931
$2.10
excluding VAT
6
Bolt Hex M12x1.5x 80 RH 10.9 ST DIN 960
B01112150080R3SD960
$8.90
excluding VAT
7
Washer FlatSmall M12 ZN DIN433
B03212NAZD433
$2.10
excluding VAT
8
Nut Nylock M12x1.5 RH 8.8 ZN DIN985-8
B02212150R2ZD9858
$2.10
excluding VAT
9
Ackermann Washer Round 0 offset
WF013_140
$10.00
excluding VAT
10
Ackermann Washer Round 3 Offset
WF080_142
$10.00
excluding VAT
11
Ackermann Washer Round 6 Offset
WF080_144
$10.00
excluding VAT
12
Bolt Hex M10x1.5x 70 RH 10.9 ST DIN 931
B01110150070R3SD931
$4.00
excluding VAT
13
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$2.10
excluding VAT
14
Rod end 14x1.5 RH female CrMo
SRODEND14X1.5 RH F
$36.00
excluding VAT
15
Spacer ID10 OD14 h13
WF370_909
$12.00
excluding VAT
16
Spacer ID10 OD14 h 9
WF861_903
$10.00
excluding VAT

Left Lower Control Arm

Left Lower Control Arm

1
Lower Control Arm
Left
WFC60_200LA
$510.00
excluding VAT
2
Spherical ID16/OD32
SSPHERICAL 16/32
$35.00
excluding VAT
3
Rod end 18x1.5 RH male CrMo
SRODEND18X1.5 RH M
$45.00
excluding VAT
4
Spacer ID12 OD16 h10
WFC60_901
$12.00
excluding VAT
5
Spacer ID12 OD16 h11
WF981_902
$12.00
excluding VAT
6
Spacer ID12 OD16 h19
WF861_901
$12.00
excluding VAT
7
Double Adjuster Female/Male M18x1.5 M27x1.5 Allen
WF452_901
$35.00
excluding VAT
8
Bolt Hex M10x1.5x 35 RH 10.9 ST DIN 933
B01110150035R3SD933
$4.00
excluding VAT
9
Washer Flat M10 ZN DIN125
B03110NAZD125
$2.10
excluding VAT
10
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$2.10
excluding VAT
11
Bolt Hex M 8x1.25x 25 RH 12.9 ST DIN 933
B01108125025R4SD933
$2.10
excluding VAT
12
Washer Flat M 8 ZN DIN125
B03108NAZD125
$2.10
excluding VAT
13
Double Adjuster Locknut M18x1.5 Allen
WF452_902
$19.00
excluding VAT
14
C-Clip InternalSTD d32 ST DIN472
B04132SD472
$2.10
excluding VAT

Right Lower Control Arm

Right Lower Control Arm

1
Lower Control Arm
Right
WFC60_200RA
$510.00
excluding VAT
2
Spherical ID16/OD32
SSPHERICAL 16/32
$35.00
excluding VAT
3
Rod end 18x1.5 RH male CrMo
SRODEND18X1.5 RH M
$45.00
excluding VAT
4
Spacer ID12 OD16 h10
WFC60_901
$12.00
excluding VAT
5
Spacer ID12 OD16 h11
WF981_902
$12.00
excluding VAT
6
Spacer ID12 OD16 h19
WF861_901
$12.00
excluding VAT
7
Double Adjuster Female/Male M18x1.5 M27x1.5 Allen
WF452_901
$35.00
excluding VAT
8
Bolt Hex M10x1.5x 35 RH 10.9 ST DIN 933
B01110150035R3SD933
$4.00
excluding VAT
9
Washer Flat M10 ZN DIN125
B03110NAZD125
$2.10
excluding VAT
10
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$2.10
excluding VAT
11
Bolt Hex M 8x1.25x 25 RH 12.9 ST DIN 933
B01108125025R4SD933
$2.10
excluding VAT
12
Washer Flat M 8 ZN DIN125
B03108NAZD125
$2.10
excluding VAT
13
Double Adjuster Locknut M18x1.5 Allen
WF452_902
$19.00
excluding VAT
14
C-Clip InternalSTD d32 ST DIN472
B04132SD472
$2.10
excluding VAT
15
Nut Hex Flange M 8x1.25 RH 8.8 ZN
B02508125R2ZD69238
$2.10
excluding VAT

Upper Control Arm

Upper Control Arm

1
Upper Control Arm
WFC60_300A
$300.00
excluding VAT
2
Upper Arm Mount
WFC60_902
$35.00
excluding VAT
3
Rod end 16x1.5 RH male CrMo
SRODEND16X1.5 RH M
$36.00
excluding VAT
4
Nut Thin M16x1.5 RH 8.8 ZN DIN936/439
B02316150R2ZD936/439
$4.00
excluding VAT
5
Washer Flat M12 ZN DIN125
B03112NAZD125
$2.10
excluding VAT
6
Bolt Hex M12x1.5x 60 RH 10.9 ST DIN 960
B01112150060R3SD960
$6.00
excluding VAT
7
Nut Nylock M12x1.5 RH 8.8 ZN DIN985-8
B02212150R2ZD9858
$2.10
excluding VAT
8
Spacer ID12 OD16 h 4.5
WF144_903
$12.00
excluding VAT

Tie Rod Assembly

Tie Rod Assembly

1
Tie Rod Assembly
WFC60_600A
$60.00
excluding VAT
2
Tie Rod Inner M14x1.5 M14x1.5 L360
STIEROD_M14_M14_L360
$30.00
excluding VAT
3
Rack Extender M14x1.5 M18x1.5 L24
WF900_901
$21.00
excluding VAT
Wisefab Nissan 240sx
"’We started working together with Wisefab back in 2014 when we launched our Falken Tyres Nissan 240sx for European competition. Since then, we have enjoyed working closely with the engineers at Wisefab testing new products before going into production and have had a lot of success winning multiple championship worldwide. Thank you to everyone at Wisefab for believing in us and producing such top-quality products."
Nissan 240sx Drift
“When I first installed a Wisefab lock kit it truly opened the door for some more aggressive driving style. I quickly began to expect nothing less than the massive angle and performance that Wisefab provides and installed a lock kit on all (4) of my Nissan 240sx that I currently drift. Also, after testing what I though was a very competitive rear suspension solution against the latest Wisefab rear kit, I was blown away with the apparent grip gain the rear Wisefab kit yielded. I am so thankful that Wisefab has poured so much effort into creating a bolt on suspension solution that transforms a Nissan 240sx into what I believe is still the most competitive drift chassis in the world."
Nissan 240sx Lock kit
"I love the Wisefab suspension kits used on my competition and demo vehicles, they provide all the angle and grip we love along with the strength and durability we need to compete with the best!"
Toyota 86 Drift
"I wouldn't have half the results! Only by running Wisefab in my Toyota 86 it just makes the car handle so good and let's me adjust set up pretty easy which is a massive help going from track to track!"