Nissan S Chassis Rear Halfshaft Kit

$1,690.00
excluding VAT
In stock
SKU
WF1419
or View Spares

Wisefab Dynamic Halfshaft Axles can hold 1500hp and offer outstanding reliability.  Our axles use CV joints with low wear and high strength. The key is superior shaft material that not only has high-yield strength, but can also survive deformations or twists.

S-chassis halfshaft kit includes 2 x fully assembled axles and 2 x custom 30 spline hubs that will fit to OEM S-chassis wheel bearing. The inner flange has 6x94mm (6x3.7") bolt pattern that fits to Winters 930 CV joint flange.

Read full description

We, at Wisefab, always strive to engineer the best products that allow drivers to push their limits on the track. Behind our unique designs are countless hours of research, problem-solving, and meticulous development. Wisefab Dynamic Halfshaft Axles can hold 1500hp and offer outstanding reliability. We designed the axle shaft strength to be just a little below the strength of differential output shafts. Our axles use CV joints with low wear and high strength. As expensive drivetrain components become common place in most rally, drift, and race cars, it is important to create a system between them that helps with their longevity. The key is superior shaft material that not only has high-yield strength, but can also survive deformations or twists. In the case when some part in a drivetrain has to give, Wisefab shafts will take the abuse. Our shafts will flex to absorb the excess of critical torque. In these situations, Wisefab shafts can twist to at least 90 degrees, often times reaching 180 degrees or even 360 degrees without failure, allowing you to finish your race in one piece. Keep in mind that any twisting won’t happen until the torque limit has been reached. If your shafts do twist more than 90 degrees, it is recommended to replace the shaft.

 

  • Max hp rating 1500 hp
  • 6x94 (6x3.7") inner bolt pattern that fits to Winters 930 CV joint flange
  • Set comes with custom 30 spline press-in hubs that fits into S-chassis OEM wheel bearing 
  • Max CV operating angle: outer 50 deg / inner 25 deg
  • Max allowed permanent shaft flex before replacement: 90 degrees
More Information
Make Nissan
Field Halfshafts
Placement Rear
Prodmaster Name Halfshaft Kit

Spare parts

All
Complete parts
Halfshaft Assembly

Complete parts

Complete parts

1
Halfshaft Assembly
WF1419_100A
$910.00
excluding VAT

Halfshaft Assembly

Halfshaft Assembly

1
Halfshaft Assembly
WF1419_100A
$910.00
excluding VAT
2
Drive Flange Adapter
WF369_902
$95.00
excluding VAT
3
Halfshaft
WF909_901
$425.00
excluding VAT
4
Metal Tightening Strap 338
B0719301338
$2.00
excluding VAT
5
C-Clip Internal Snap Ring STD d30 ST DIN7993B
B04330SD7993B
$2.00
excluding VAT
6
CV Joint Bellow Large
SBellow 30X98X122
$34.00
excluding VAT
7
Metal Tightening Strap 086
B0716700086
$2.00
excluding VAT
8
Metal Tightening Strap 102
B0716700102
$2.00
excluding VAT
9
CV Joint Outer
WF369_905
$320.00
excluding VAT
10
Spacer bushing
WF369_906
$8.50
excluding VAT
11
Nut DHEX Flange M24x1.5
B02524150R2ZSPC15
$8.50
excluding VAT
12
Bolt Allen M12x1.5x 50 RH 12.9 ST DIN 912
B01212150050R4SD912
$9.90
excluding VAT
13
CV Joint Bellow Small
SBellow 25X77X94
$34.00
excluding VAT
14
CV Joint Inner
SCVJoint33G30
$295.00
excluding VAT
15
C-Clip ExternalSTD d30 ST DIN471
B04230SD471
$2.00
excluding VAT
16
Bolt Allen 3/8-24 UNF RH 12.9 ST DIN912 A574
B01210100015R4SD912
$11.00
excluding VAT
17
CV Joint Grease 80g
SCVJoint Grease
$3.60
excluding VAT
18
Wheel Hub
WF1419_500A
$140.00
excluding VAT