Mazda RX-8 Front Lock Kit

$2,100.00
excluding VAT
In stock
SKU
WFR80 LHD
or View Spares

All the steel components on RX8 front suspension are from high strenght steel, including sheetmetal components, tubes, tube ends and rod end housings. Rod ends and spherical bearings are used, no OEM bushings. The kit comes also with new 7075 aluminium billet U-joint to connect the Mazda steering column to the BMW rack. 

Read full description
  • Suitable for Mazda RX8 and MX5 NC (2005 – 2015)
    The kit comes with parts to fit a BMW E36 or E46 rack to the subframe. The knuckle has 2 positions for tie rod attachment: for original rack position and for a lowered position. For lowered position it has also some adjustability in case someone has already lowered the rack and it doesn't match with our designed height.
  • 65 degrees of lock, parallel steering
    You can tune your steering geometry either towards positive or negative Ackermann in just a few minutes even at trackside without messing up the alignment. The Ackermann adjustment kit is included.
  • Adjustable lock stopper
  • Higher roll center (RC)
    On Wisefab knuckles, both joints are dropped, which brings the front RC up on a lowered car, providing higher roll stiffness, good camber control and minimal bump steer with high steering angles. With our kinematics we have assured that the camber will provide very good front grip and bump steer is minimal throughout the steering range.
  • Steering jacking control
    During drifting, when steering angle is increased, jacking is also bigger, even with the same geometry it could become a problem. We have changed the geometry in a way that doesn't cause any handling issues.
  • Consistent and predictable self-alignment torque
    Caster is not the only important parameter to provide sufficient self-alignment torque, especially at high lock. It's the combination of different parameters to maintain consistent trail and self-alignment torque. With our setup the steering wheel turns always to the direction of movement and doesn't get stuck at full lock.

Kit includes:

  • Upper and lower control arms
  • Knuckles with hardware
  • Assembeled tie rods
  • Rack relocating kit
  • Installation guide

 

 

Other information:

  • This kit assumes coilovers for enough clearance
  • Ride height is designed to be ~80mm when measured from the subframe to the ground
  • Dependent on rim width and ET, widened fenders or flares will be needed
  • Inner wheel wells do not need to be modified with tire diameter up to 635mm (215/45R17, 225/45R17, 235/40R17, 225/40R18 etc)
  • Minimum rim size is 17"
  • Recommended backspacing is ~135mm (7" ET45; 8" ET35; 9" ET20). If ET is smaller, then wheels stay more outwards, if ET is bigger, then spacers need to be used
  • Original wheelspeed sensor (ABS sensor) can be used
  • Original swaybar can be used in front
More Information
Make Mazda
Field Drift
Placement Front
Prodmaster Name Lock Kit
color_swatch No
"’We started working together with Wisefab back in 2014 when we launched our Falken Tyres S14 for European competition. Since then, we have enjoyed working closely with the engineers at Wisefab testing new products before going into production and have had a lot of success winning multiple championship worldwide. Thank you to everyone at Wisefab for believing in us and producing such top-quality products."

Spare parts

All
Complete parts
Left Knuckle
Right Knuckle
Left Lower Control Arm
Right Lower Control Arm
Upper Control Arm
Left Tie Rod Assembly
Right Tie Rod Assembly
Steering Rack Template LHD
Steering Column Universal Joint

Complete parts

Complete parts

1
Knuckle
Left
WFR80_100LA
$435.00
excluding VAT
Right
WFR80_100RA
$435.00
excluding VAT
2
Lower Control Arm
Left
WFR80_200LA
$365.00
excluding VAT
Right
WFR80_200RA
$365.00
excluding VAT
3
Upper Control Arm
WFR80_300A
$250.00
excluding VAT
4
Tie Rod Assembly
Left
WFR80_600LA
$90.00
excluding VAT
Right
WFR80_600RA
$110.00
excluding VAT
5
Steering Rack Template LHD
WFR80_400A LHD
$135.00
excluding VAT
6
Steering Column Universal Joint
WFR80_700A
$250.00
excluding VAT

Left Knuckle

Left Knuckle

1
Knuckle
Left
WFR80_100LA
$435.00
excluding VAT
2
Bolt Hex M 8x1.25x 70 RH 8.8 ZN DIN 931
B01108125070R2ZD931
$1.80
excluding VAT
3
BushingT ID 8 OD22 h51 Excentric Lock Stopper
WF370_950
$14.00
excluding VAT
4
Nut Nylock M 8x1.25 RH 8.8 ZN DIN985-8
B02208125R2ZD9858
$1.80
excluding VAT
5
Bolt Hex M12x1.5x 70 RH 10.9 ST DIN 960
B01112150070R3SD960
$8.00
excluding VAT
6
Washer FlatSmall M12 ZN DIN433
B03212NAZD433
$1.80
excluding VAT
7
BushingT ID12 OD28 h11
WF180_905
$10.00
excluding VAT
8
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$1.80
excluding VAT
9
Ackermann Washer Round 0 offset
WF013_140
$9.00
excluding VAT
10
Ackermann Washer Round 3 Offset
WF080_142
$9.00
excluding VAT
11
Ackermann Washer Round 6 Offset
WF080_144
$9.00
excluding VAT
12
BushingT ID10 OD29.5 h 5.5
WFR80_909
$9.00
excluding VAT
13
BushingT ID10 OD29.5 h41 Special
WFR80_905
$14.00
excluding VAT
14
Bolt Hex M10x1.5x110 RH 10.9 ST DIN 931
B01110150110R3SD931
$5.00
excluding VAT
15
Washer FlatSmall M10 ZN DIN433
B03210NAZD433
$1.80
excluding VAT
16
Bolt Hex M10x1.5x 60 RH 10.9 ST DIN 931
B01110150060R3SD931
$3.40
excluding VAT
17
Hub Spacer
WFR80_101
$15.00
excluding VAT

Right Knuckle

Right Knuckle

1
Knuckle
Right
WFR80_100RA
$435.00
excluding VAT
2
Bolt Hex M 8x1.25x 70 RH 8.8 ZN DIN 931
B01108125070R2ZD931
$1.80
excluding VAT
3
BushingT ID 8 OD22 h51 Excentric Lock Stopper
WF370_950
$14.00
excluding VAT
4
Nut Nylock M 8x1.25 RH 8.8 ZN DIN985-8
B02208125R2ZD9858
$1.80
excluding VAT
5
Bolt Hex M12x1.5x 70 RH 10.9 ST DIN 960
B01112150070R3SD960
$8.00
excluding VAT
6
Washer FlatSmall M12 ZN DIN433
B03212NAZD433
$1.80
excluding VAT
7
BushingT ID12 OD28 h11
WF180_905
$10.00
excluding VAT
8
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$1.80
excluding VAT
9
Ackermann Washer Round 0 offset
WF013_140
$9.00
excluding VAT
10
Ackermann Washer Round 3 Offset
WF080_142
$9.00
excluding VAT
11
Ackermann Washer Round 6 Offset
WF080_144
$9.00
excluding VAT
12
BushingT ID10 OD29.5 h 5.5
WFR80_909
$9.00
excluding VAT
13
BushingT ID10 OD29.5 h41 Special
WFR80_905
$14.00
excluding VAT
14
Bolt Hex M10x1.5x110 RH 10.9 ST DIN 931
B01110150110R3SD931
$5.00
excluding VAT
15
Washer FlatSmall M10 ZN DIN433
B03210NAZD433
$1.80
excluding VAT
16
Bolt Hex M10x1.5x 60 RH 10.9 ST DIN 931
B01110150060R3SD931
$3.40
excluding VAT
17
Hub Spacer
WFR80_101
$15.00
excluding VAT

Left Lower Control Arm

Left Lower Control Arm

1
Lower Control Arm
Left
WFR80_200LA
$365.00
excluding VAT
2
Spacer ID14 OD16 h19
WF180_910
$10.00
excluding VAT
3
Rod end 16x1.5 RH male CrMo
SRODEND16X1.5 RH M
$35.00
excluding VAT
4
Nut Thin M16x1.5 RH 8.8 ZN DIN936/439
B02316150R2ZD936/439
$3.40
excluding VAT
5
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$1.80
excluding VAT
6
Washer Flat M10 ZN DIN125
B03110NAZD125
$1.80
excluding VAT
7
Spacer ID12 OD16 h14.5
WF113_913
$10.00
excluding VAT
8
Lower Control Arm Spherical Shock Mount
WF350_700A
$50.00
excluding VAT
9
Bolt Hex M10x1.5x 35 RH 10.9 ST DIN 933
B01110150035R3SD933
$3.40
excluding VAT
10
Spacer ID12 OD16 h10
WF013_903
$10.00
excluding VAT
11
C-Clip InternalSTD d32 ST DIN472
B04132SD472
$1.80
excluding VAT
12
Spherical ID16/OD32
SSPHERICAL 16/32
$30.00
excluding VAT

Right Lower Control Arm

Right Lower Control Arm

1
Lower Control Arm
Right
WFR80_200RA
$365.00
excluding VAT
2
Spacer ID14 OD16 h19
WF180_910
$10.00
excluding VAT
3
Rod end 16x1.5 RH male CrMo
SRODEND16X1.5 RH M
$35.00
excluding VAT
4
Nut Thin M16x1.5 RH 8.8 ZN DIN936/439
B02316150R2ZD936/439
$3.40
excluding VAT
5
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$1.80
excluding VAT
6
Washer Flat M10 ZN DIN125
B03110NAZD125
$1.80
excluding VAT
7
Spacer ID12 OD16 h14.5
WF113_913
$10.00
excluding VAT
8
Lower Control Arm Spherical Shock Mount
WF350_700A
$50.00
excluding VAT
9
Bolt Hex M10x1.5x 35 RH 10.9 ST DIN 933
B01110150035R3SD933
$3.40
excluding VAT
10
Spacer ID12 OD16 h10
WF013_903
$10.00
excluding VAT
11
C-Clip InternalSTD d32 ST DIN472
B04132SD472
$1.80
excluding VAT
12
Spherical ID16/OD32
SSPHERICAL 16/32
$30.00
excluding VAT

Upper Control Arm

Upper Control Arm

1
Upper Control Arm
WFR80_300A
$250.00
excluding VAT
2
Spacer ID12 OD14 h29.5
WFR80_904
$10.00
excluding VAT
3
Rod end 14x1.5 LH male CrMo
SRODEND14X1.5 LH M
$25.00
excluding VAT
4
Spacer ID12 OD14 h 5.5
WFR80_903
$9.00
excluding VAT
5
Nut Thin M14x1.5 LH 8.8 ZN DIN936/439
B02314150L2ZD936/439
$3.40
excluding VAT
6
Spacer ID10 OD12 h10.5
WF113_902
$9.00
excluding VAT
7
C-Clip InternalSTD d26 ST DIN472
B04126SD472
$1.80
excluding VAT
8
Spherical ID12/OD26
SSPHERICAL 12/26
$30.00
excluding VAT

Left Tie Rod Assembly

Left Tie Rod Assembly

1
Tie Rod Assembly
Left
WFR80_600LA
$90.00
excluding VAT
2
Rack Extender M14x1.5 M18x1.5 L24
WF900_901
$18.00
excluding VAT
3
Tie Rod Inner M14x1.5 M14x1.5 L366
STIEROD_M14_M14_L366
$25.00
excluding VAT
4
Spacer ID10 OD14 h 5.4
WF080_921
$9.00
excluding VAT
5
Rod end 14x1.5 RH female CrMo
SRODEND14X1.5 RH F
$35.00
excluding VAT

Right Tie Rod Assembly

Right Tie Rod Assembly

1
Tie Rod Assembly
Right
WFR80_600RA
$110.00
excluding VAT
2
Rack Extender M14x1.5 M18x1.5 L110
WFR80_906
$40.00
excluding VAT
3
Tie Rod Inner M14x1.5 M14x1.5 L366
STIEROD_M14_M14_L366
$25.00
excluding VAT
4
Spacer ID10 OD14 h 5.4
WF080_921
$9.00
excluding VAT
5
Rod end 14x1.5 RH female CrMo
SRODEND14X1.5 RH F
$35.00
excluding VAT

Steering Rack Template LHD

Image currently unavailable

Steering Rack Template LHD

1
Steering Rack Template LHD
WFR80_400A LHD
$135.00
excluding VAT

Steering Column Universal Joint

Steering Column Universal Joint

1
Steering Column Universal Joint
WFR80_700A
$250.00
excluding VAT
2
Bolt Hex M 8x1.25x 25 RH 12.9 ST DIN 933
B01108125025R4SD933
$1.80
excluding VAT
3
Washer Flat M 8 ZN DIN125
B03108NAZD125
$1.80
excluding VAT
4
Bolt AllenButton M 4x0.7x 6 RH 8.8 ZN ISO7380
B01404070006R2ZI7380
$1.80
excluding VAT
5
Universal Joint 16x40
SUJOINT1640
$35.00
excluding VAT