BMW E9x Front Lock Kit

$1,750.00
excluding VAT
In stock
SKU
WF900
or View Spares

Wisefab BMW e9x suspension kit can be fitted on a variety of BMW models. E90, E91, E92, E81, E82, E87, E88 M and nonM. Brackets included to fit M brake caliper. Either M or nonM front coilovers would work with Wisefab E90 knuckle. All the metal components on Wisefab E90 front suspension are from high strenght steel, including sheetmetal components, tubes, tube ends and rod end housings. Rod ends and spherical bearings are used, no rubber bushings.

Read full description
  • 65 degrees of lock, parallel steering. 
    You could tune your steering geometry either towards positive or negative Ackermann in just a few minutes even at trackside without messing up an alignment. 
    Ackermann adjustment kit included.
  • Adjustable lock stopper.
  • One piece lower control arm desing. 
    Lower links are replaced with one arm. Drifting with higher steering angle the stiffness and packaging would become an issue. Therefore lower one piece arm is used.
  • Higher roll center (RC). 
    On Wisefab knuckle, joints are dropped, which brings the front RC up on lowered car, providing higher roll stiffness and letting to remove the front anti roll bar (sway bar) that is quite difficult to package with that high lock angles. 
  • Very good camber control and minimal bump steer with high steering angles. 
    On drift cars the dynamic camber and bump steer is much more important than static. With our kinematics we have assured that the camber would provide very good front grip and bump steer is minimal at all the range of steering.
  • Steering jacking control.
    During drifting, when steering angle is much bigger, jacking is also bigger, even with the same geometry and it could become a problem. We have changed the geometry that it doesn’t cause any handling issues.
  • Consistent and predictable self-alignment torque. 
    Caster is not the only important parameter to provide sufficient self-alignment torque especially at high lock. It’s the combination of different parameters to maintain consistent trail and self-alignment torque. With our setup the steering wheel turns always to the direction of movement and doesn’t get stuck at full lock. 
  • Original wheelspeed sensor (ABS sensor) can be used.

Kit includes:

  • Adjustable coilover upper mounts, Formula Drift compliance.
  • Knuckles with hardware.
  • Lower control arms.
  • Assembeled tie rods.
  • Brake adapters for M model brakes.
  • 45mm coilover adapter sleeve.
  • Installation guide.

 

 Other components, packaging and clearance.

  • This kit assumes coilovers, to have enough clearance. 
  • Ride height is designed to be ~80mm from front subframe to ground.
  • Dependent on rim width and ET, wider fenders or fender flares would be needed.
  • Inner wheel wells do not need to be modified with tire diameter up to 635mm (215/45R17, 225/45R17, 235/40R17, 225/40R18 etc).
  • Minimum rim diameter is 17”.
  • Recommended backspacing is ~135mm (7“ ET45; 8“ ET35; 9“ ET20).
  • If ET is smaller, then wheels stay more outwards, if ET is bigger, then spacers need to be used.
  • The kit is designed and manufactured the way that after installation and toe adjustment it’s ready to use right away.
More Information
Make BMW
Field Drift
Placement Front
Prodmaster Name Lock Kit
color_swatch No
"’We started working together with Wisefab back in 2014 when we launched our Falken Tyres S14 for European competition. Since then, we have enjoyed working closely with the engineers at Wisefab testing new products before going into production and have had a lot of success winning multiple championship worldwide. Thank you to everyone at Wisefab for believing in us and producing such top-quality products."

Spare parts

All
Complete parts
Left Knuckle
Right Knuckle
Left Lower Control Arm
Right Lower Control Arm
Tie Rod Assembly
M3 Brake Adapter
Top Mount

Complete parts

Complete parts

1
Knuckle
Left
WF900_100LA
$415.00
excluding VAT
Right
WF900_100RA
$415.00
excluding VAT
2
Lower Control Arm
Left
WF900_200LA
$340.00
excluding VAT
Right
WF900_200RA
$340.00
excluding VAT
3
Tie Rod Assembly
WF900_600A
$85.00
excluding VAT
4
M3 Brake Adapter
WF900_400A
$75.00
excluding VAT
5
Top Mount
WF900_500A
$125.00
excluding VAT

Left Knuckle

Left Knuckle

1
Knuckle
Left
WF900_100LA
$415.00
excluding VAT
2
Strut Adapter
WF900_906
$24.00
excluding VAT
3
Bolt Hex M10x1.5x 70 RH 10.9 ST DIN 931
B01110150070R3SD931
$3.40
excluding VAT
4
Ackermann Washer Round 0 offset
WF013_140
$9.00
excluding VAT
5
Ackermann Washer Round 3 Offset
WF080_142
$9.00
excluding VAT
6
Ackermann Washer Round 6 Offset
WF080_144
$9.00
excluding VAT
7
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$1.80
excluding VAT
8
Bolt Hex M12x1.5x 60 RH 10.9 ST DIN 960
B01112150060R3SD960
$5.00
excluding VAT
9
Washer FlatSmall M12 ZN DIN433
B03212NAZD433
$1.80
excluding VAT
10
Bolt AllenButton M 8x1.25x 60 RH 8.8 ZN ISO7380
B01408125060R2ZI7380
$3.40
excluding VAT
11
BushingT ID 8 OD22 h41 Excentric Lock Stopper
WF350_950
$14.00
excluding VAT
12
Washer Flat M 8 ZN DIN125
B03108NAZD125
$1.80
excluding VAT
13
Nut Nylock M 8x1.25 RH 8.8 ZN DIN985-8
B02208125R2ZD9858
$1.80
excluding VAT

Right Knuckle

Right Knuckle

1
Knuckle
Right
WF900_100RA
$415.00
excluding VAT
2
Strut Adapter
WF900_906
$24.00
excluding VAT
3
Bolt Hex M10x1.5x 70 RH 10.9 ST DIN 931
B01110150070R3SD931
$3.40
excluding VAT
4
Ackermann Washer Round 0 offset
WF013_140
$9.00
excluding VAT
5
Ackermann Washer Round 3 Offset
WF080_142
$9.00
excluding VAT
6
Ackermann Washer Round 6 Offset
WF080_144
$9.00
excluding VAT
7
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$1.80
excluding VAT
8
Bolt Hex M12x1.5x 60 RH 10.9 ST DIN 960
B01112150060R3SD960
$5.00
excluding VAT
9
Washer FlatSmall M12 ZN DIN433
B03212NAZD433
$1.80
excluding VAT
10
Bolt AllenButton M 8x1.25x 60 RH 8.8 ZN ISO7380
B01408125060R2ZI7380
$3.40
excluding VAT
11
BushingT ID 8 OD22 h41 Excentric Lock Stopper
WF350_950
$14.00
excluding VAT
12
Washer Flat M 8 ZN DIN125
B03108NAZD125
$1.80
excluding VAT
13
Nut Nylock M 8x1.25 RH 8.8 ZN DIN985-8
B02208125R2ZD9858
$1.80
excluding VAT

Left Lower Control Arm

Left Lower Control Arm

1
Lower Control Arm
Left
WF900_200LA
$340.00
excluding VAT
2
Spacer ID12 OD16 h24.5
WF900_902
$10.00
excluding VAT
3
Rod end 16x1.5 RH male CrMo
SRODEND16X1.5 RH M
$35.00
excluding VAT
4
Nut Thin M16x1.5 RH 8.8 ZN DIN936/439
B02316150R2ZD936/439
$3.40
excluding VAT
5
Washer FlatLarge M12 ZN SFS3738
B03512ZSFS3738
$1.80
excluding VAT
6
Spacer ID12 OD16 h10
WF013_903
$10.00
excluding VAT
7
C-Clip InternalSTD d32 ST DIN472
B04132SD472
$1.80
excluding VAT
8
Spherical ID16/OD32
SSPHERICAL 16/32
$30.00
excluding VAT

Right Lower Control Arm

Right Lower Control Arm

1
Lower Control Arm
Right
WF900_200RA
$340.00
excluding VAT
2
Spacer ID12 OD16 h24.5
WF900_902
$10.00
excluding VAT
3
Rod end 16x1.5 RH male CrMo
SRODEND16X1.5 RH M
$35.00
excluding VAT
4
Nut Thin M16x1.5 RH 8.8 ZN DIN936/439
B02316150R2ZD936/439
$3.40
excluding VAT
5
Washer FlatLarge M12 ZN SFS3738
B03512ZSFS3738
$1.80
excluding VAT
6
Spacer ID12 OD16 h10
WF013_903
$10.00
excluding VAT
7
C-Clip InternalSTD d32 ST DIN472
B04132SD472
$1.80
excluding VAT
8
Spherical ID16/OD32
SSPHERICAL 16/32
$30.00
excluding VAT

Tie Rod Assembly

Tie Rod Assembly

1
Tie Rod Assembly
WF900_600A
$85.00
excluding VAT
2
Tie Rod Inner M14x1.5 M14x1.5 L360
STIEROD_M14_M14_L360
$25.00
excluding VAT
3
Rack Extender M14x1.5 M18x1.5 L24
WF900_901
$18.00
excluding VAT
4
Rod end 14x1.5 RH female CrMo
SRODEND14X1.5 RH F
$35.00
excluding VAT
5
Spacer ID10 OD14 h11
WF013_901
$9.00
excluding VAT

M3 Brake Adapter

M3 Brake Adapter

1
M3 Brake Adapter
WF900_400A
$75.00
excluding VAT
2
Bolt HexThin M12x1.50x 50 RH 10.9 ST SPC
WF900_908
$13.00
excluding VAT
3
Bolt Hex M12x1.5x 50 RH 10.9 ST DIN 961
B01112150050R3SD961
$5.00
excluding VAT
4
Nut Nylock M12x1.5 RH 8.8 ZN DIN985-8
B02212150R2ZD9858
$1.80
excluding VAT
5
Washer FlatSmall M12 ZN DIN433
B03212NAZD433
$1.80
excluding VAT

Top Mount

Top Mount

1
Top Mount
WF900_500A
$125.00
excluding VAT
2
Camber Plate Spherical Housing REG
WF013_917A
$65.00
excluding VAT
3
Nut Hex Flange M 8x1.25 RH 8.8 ZN
B02508125R2ZD69238
$1.80
excluding VAT
4
Bolt AllenFlat M 6x1.0x 16 RH 8.8 ZN DIN7991
B01306100016R2SD7991
$1.80
excluding VAT
5
Bolt Hex M 8x1.25x 16 RH 8.8 ZN DIN 933
B01108125016R2ZD933
$1.80
excluding VAT