Toyota GT86 Front Lock Kit LHD

$2,700.00
excluding VAT
In stock
SKU
WF860 LHD
or View Spares

Due to the boxer engine, the original steering rack location is very unsuitable for drifting, therefore the steering rack has been moved from under the front crossmember with the possibility to use either the boxer engine or I6/V8 or something else. Nissan S-Chassis hydraulic steering rack ( 50mm outer diameter ) is needed to be used with the kit to replace the original electric power steering. S-Chassis steering rack attachment/crossmember insert along with crossmember supports are included in the kit. To modify the crossmember some DIY cutting and welding needs to be done.

Read full description
  • 62 degrees of lock, parallel steering
    You can tune your steering geometry towards positive Ackermann in just a few minutes even at trackside without messing up the alignment. Ackermann adjustment is included in the kit.
  • 7 kg of weight reduction
    While still maintaining the required strength and stiffness.
  • 7075-T6 aluminium
    Billet CNC knuckles and arms with optimized design and all double shear connections provide low weight and high strenght.
  • CrMo rod ends and sphericals used instead of OEM bushings
  • Higher roll center (RC)
    With our knuckle, the ball joint is lowered, which brings the front RC up on a lowered car, providing higher roll stiffness. This allows to remove the front anti roll-bar (sway bar) that is quite difficult to package with high lock angles.
  • Good camber control and minimal bump steer with high steering angles
    On drift cars the dynamic camber and bump steer is much more important than static. With our kinematics we have assured that the camber will provide very good front grip and bump steer is minimal throughout the steering range.
  • Steering jacking control
    During drifting, when steering angle is increased, jacking is also bigger, even with the same geometry it could become a problem. We have changed the geometry in a way that doesn't cause any handling issues.
  • Consistent and predictable self-alignment torque. 
    Caster is not the only important parameter to provide sufficient self-alignment torque, especially at high lock. It's the combination of different parameters to maintain consistent trail and self-alignment torque. With our setup the steering wheel turns always to the direction of movement and doesn't get stuck at full lock.

Kit includes:

  • Pre-set lower control arms
  • Knuckles with hardware
  • Assembeled tie rods
  • Pre-set coilover upper mounts
  • Rack relocating kit
  • Crossmember supports
  • Installation guide

 

Other information:

  • This kit assumes coilovers for enough clearance
  • Dependent on rim width and ET, wider fenders or fender flares are needed.
  • Due to extremely wide engine bay on Subaru BRZ, we recommend using tires no bigger than 605mm (215/40R17, 225/40R17, 215/35R18, 225/35R18)
  • With tire diameter up to 635mm (215/45R17, 225/45R17, 235/40R17, 225/40R18 etc) and lowered ride height the inner wheel wells need to be slightly modified.
  • Minimum rim size is 17“, but we recommend using 18“
  • Recommended backspacing is 135-140mm (7“ ET45; 8“ ET35; 9“ ET25). If ET is smaller, then wheels stay more outwards, if ET is bigger, then spacers need to be used.
  • Original wheel speed sensor can be used
More Information
Make Toyota
Field Drift
Placement Front
Prodmaster Name Lock Kit LHD
color_swatch No
"’We started working together with Wisefab back in 2014 when we launched our Falken Tyres S14 for European competition. Since then, we have enjoyed working closely with the engineers at Wisefab testing new products before going into production and have had a lot of success winning multiple championship worldwide. Thank you to everyone at Wisefab for believing in us and producing such top-quality products."

Spare parts

All
Complete parts
Left Knuckle
Right Knuckle
Left Lower Control Arm
Right Lower Control Arm
Left Tie Rod Assembly
Right Tie Rod Assembly
Left Top Mount
Right Top Mount
Left Subframe Support
Right Subframe Support
Steering Rack Support
Steering Column Extender

Complete parts

Complete parts

1
Knuckle
Left
WF860_100LA
$690.00
excluding VAT
Right
WF860_100RA
$690.00
excluding VAT
2
Lower Control Arm
Left
WF860_200LA
$470.00
excluding VAT
Right
WF860_200RA
$470.00
excluding VAT
3
Tie Rod Assembly
Left
WF860_600LA
$90.00
excluding VAT
Right
WF860_600RA
$90.00
excluding VAT
4
Top Mount
Left
WF860_500LA
$250.00
excluding VAT
Right
WF860_500RA
$250.00
excluding VAT
5
Subframe Support
Left
WF860_400L
$65.00
excluding VAT
Right
WF860_400R
$65.00
excluding VAT
6
Steering Rack Support
WF860_700A_LHD
$135.00
excluding VAT
7
Steering Column Extender
WF860_750A
$200.00
excluding VAT

Left Knuckle

Left Knuckle

1
Knuckle
Left
WF860_100LA
$690.00
excluding VAT
2
Bolt Hex M10x1.5x130 RH 10.9 ST DIN 931
B01110150130R3SD931
$8.00
excluding VAT
3
Ackermann Washer Cross 0 Offset
WF860_140
$9.00
excluding VAT
4
Ackermann Washer Cross 1.5 Offset
WF860_141
$9.00
excluding VAT
5
Ackermann Washer Cross 3 Offset
WF860_142
$9.00
excluding VAT
6
Ackermann Washer Cross 4.5 Offset
WF860_143
$9.00
excluding VAT
7
BushingT ID10 OD32 h50 Special
WF860_901
$14.00
excluding VAT
8
Washer Flat M10 ZN DIN125
B03110NAZD125
$1.80
excluding VAT
9
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$1.80
excluding VAT
10
Bolt Hex M12x1.5x 70 RH 10.9 ST DIN 960
B01112150070R3SD960
$8.00
excluding VAT
11
Washer Flat M12 ZN DIN125
B03112NAZD125
$1.80
excluding VAT
12
Bolt Hex M 8x1.25x 70 RH 8.8 ZN DIN 931
B01108125070R2ZD931
$1.80
excluding VAT
13
Washer Flat M 8 ZN DIN125
B03108NAZD125
$1.80
excluding VAT
14
BushingT ID 8 OD16 h41
WF013_910
$10.00
excluding VAT
15
Nut Nylock M 8x1.25 RH 8.8 ZN DIN985-8
B02208125R2ZD9858
$1.80
excluding VAT

Right Knuckle

Right Knuckle

1
Knuckle
Right
WF860_100RA
$690.00
excluding VAT
2
Bolt Hex M10x1.5x130 RH 10.9 ST DIN 931
B01110150130R3SD931
$8.00
excluding VAT
3
Ackermann Washer Cross 0 Offset
WF860_140
$9.00
excluding VAT
4
Ackermann Washer Cross 1.5 Offset
WF860_141
$9.00
excluding VAT
5
Ackermann Washer Cross 3 Offset
WF860_142
$9.00
excluding VAT
6
Ackermann Washer Cross 4.5 Offset
WF860_143
$9.00
excluding VAT
7
BushingT ID10 OD32 h50 Special
WF860_901
$14.00
excluding VAT
8
Washer Flat M10 ZN DIN125
B03110NAZD125
$1.80
excluding VAT
9
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$1.80
excluding VAT
10
Bolt Hex M12x1.5x 70 RH 10.9 ST DIN 960
B01112150070R3SD960
$8.00
excluding VAT
11
Washer Flat M12 ZN DIN125
B03112NAZD125
$1.80
excluding VAT
12
Bolt Hex M 8x1.25x 70 RH 8.8 ZN DIN 931
B01108125070R2ZD931
$1.80
excluding VAT
13
Washer Flat M 8 ZN DIN125
B03108NAZD125
$1.80
excluding VAT
14
BushingT ID 8 OD16 h41
WF013_910
$10.00
excluding VAT
15
Nut Nylock M 8x1.25 RH 8.8 ZN DIN985-8
B02208125R2ZD9858
$1.80
excluding VAT

Left Lower Control Arm

Left Lower Control Arm

1
Lower Control Arm
Left
WF860_200LA
$470.00
excluding VAT
2
Spacer ID12 OD16 h18
WF136_903
$10.00
excluding VAT
3
Rod end 16x1.5 RH male CrMo
SRODEND16X1.5 RH M
$35.00
excluding VAT
4
Nut Thin M16x1.5 RH 8.8 ZN DIN936/439
B02316150R2ZD936/439
$3.40
excluding VAT
5
Bolt Hex M14x1.5x120 RH 10.9 ST DIN 960
B01114150120R3SD960
$10.00
excluding VAT
6
Washer Flat M14 ZN DIN125
B03114NAZD125
$1.80
excluding VAT
7
Spacer ID14 OD16 h10
WF036_903
$10.00
excluding VAT
8
Spacer ID14 OD16 h29
WF860_902
$10.00
excluding VAT
9
Spacer ID12 OD16 h10
WF013_903
$10.00
excluding VAT
10
Spherical ID16/OD32
SSPHERICAL 16/32
$30.00
excluding VAT
11
C-Clip InternalSTD d32 ST DIN472
B04132SD472
$1.80
excluding VAT

Right Lower Control Arm

Right Lower Control Arm

1
Lower Control Arm
Right
WF860_200RA
$470.00
excluding VAT
2
Spacer ID12 OD16 h18
WF136_903
$10.00
excluding VAT
3
Rod end 16x1.5 RH male CrMo
SRODEND16X1.5 RH M
$35.00
excluding VAT
4
Nut Thin M16x1.5 RH 8.8 ZN DIN936/439
B02316150R2ZD936/439
$3.40
excluding VAT
5
Bolt Hex M14x1.5x120 RH 10.9 ST DIN 960
B01114150120R3SD960
$10.00
excluding VAT
6
Washer Flat M14 ZN DIN125
B03114NAZD125
$1.80
excluding VAT
7
Spacer ID14 OD16 h10
WF036_903
$10.00
excluding VAT
8
Spacer ID14 OD16 h29
WF860_902
$10.00
excluding VAT
9
Spacer ID12 OD16 h10
WF013_903
$10.00
excluding VAT
10
Spherical ID16/OD32
SSPHERICAL 16/32
$30.00
excluding VAT
11
C-Clip InternalSTD d32 ST DIN472
B04132SD472
$1.80
excluding VAT

Left Tie Rod Assembly

Left Tie Rod Assembly

1
Tie Rod Assembly
Left
WF860_600LA
$90.00
excluding VAT
2
Rack Extender M14x1.5 M16x1.0 L85
WF860_904
$25.00
excluding VAT
3
Tie Rod Inner M14x1.5 M14x1.5 L366
STIEROD_M14_M14_L366
$25.00
excluding VAT
4
Spacer ID10 OD14 h 5.4
WF080_921
$9.00
excluding VAT
5
Rod end 14x1.5 RH female CrMo
SRODEND14X1.5 RH F
$35.00
excluding VAT

Right Tie Rod Assembly

Right Tie Rod Assembly

1
Tie Rod Assembly
Right
WF860_600RA
$90.00
excluding VAT
2
Rack Extender M14x1.5 M16x1.0 L101
WF860_903
$25.00
excluding VAT
3
Tie Rod Inner M14x1.5 M14x1.5 L366
STIEROD_M14_M14_L366
$25.00
excluding VAT
4
Spacer ID10 OD14 h 5.4
WF080_921
$9.00
excluding VAT
5
Rod end 14x1.5 RH female CrMo
SRODEND14X1.5 RH F
$35.00
excluding VAT

Left Top Mount

Left Top Mount

1
Top Mount
Left
WF860_500LA
$250.00
excluding VAT
2
Camber Plate Spherical Housing REG
WF013_917A
$65.00
excluding VAT
3
Bolt Hex M 8x1.25x 16 RH 8.8 ZN DIN 933
B01108125016R2ZD933
$1.80
excluding VAT
4
Bolt AllenFlat M 6x1.0x 16 RH 8.8 ZN DIN7991
B01306100016R2SD7991
$1.80
excluding VAT
5
Nut Hex Flange M 8x1.25 RH 8.8 ZN
B02508125R2ZD69238
$1.80
excluding VAT

Right Top Mount

Right Top Mount

1
Top Mount
Right
WF860_500RA
$250.00
excluding VAT
2
Camber Plate Spherical Housing REG
WF013_917A
$65.00
excluding VAT
3
Bolt Hex M 8x1.25x 16 RH 8.8 ZN DIN 933
B01108125016R2ZD933
$1.80
excluding VAT
4
Bolt AllenFlat M 6x1.0x 16 RH 8.8 ZN DIN7991
B01306100016R2SD7991
$1.80
excluding VAT
5
Nut Hex Flange M 8x1.25 RH 8.8 ZN
B02508125R2ZD69238
$1.80
excluding VAT

Left Subframe Support

Left Subframe Support

1
Subframe Support
Left
WF860_400L
$65.00
excluding VAT

Right Subframe Support

Right Subframe Support

1
Subframe Support
Right
WF860_400R
$65.00
excluding VAT

Steering Rack Support

Steering Rack Support

1
Steering Rack Support
WF860_700A_LHD
$135.00
excluding VAT
2
Steering Rack Support Clamp 1
WF860_730
$25.00
excluding VAT
3
Steering Rack Support Clamp 2
WF860_740
$25.00
excluding VAT
4
Bolt Hex M 8x1.25x 16 RH 8.8 ZN DIN 933
B01108125016R2ZD933
$1.80
excluding VAT
5
Washer Flat M 8 ZN DIN125
B03108NAZD125
$1.80
excluding VAT
6
Nut Nylock M 8x1.25 RH 8.8 ZN DIN985-8
B02208125R2ZD9858
$1.80
excluding VAT

Steering Column Extender

Steering Column Extender

1
Steering Column Extender
WF860_750A
$200.00
excluding VAT
2
Bolt AllenButton M 8x1.25x 25 RH 10.9 ZN ISO7380
B01408125025R3ZI7380
$1.80
excluding VAT