Nissan 350Z Front Lock Kit

$2,250.00
excluding VAT
In stock
SKU
WF350
or View Spares

Wisefab Nissan 350Z front suspension kit is about the same weight as original aluminium suspension. All the metal components on 350Z front suspension kit are from high strenght steel, including sheetmetal components, tubes, tube ends and rod end housings. Rod ends and spherical bearings are used, no rubber bushings.

Read full description
  • 65 degrees of lock, parallel steering.
    You could tune your steering geometry either towards positive or negative Ackermann in just a few minutes even at trackside without messing up an alignment. 
    Ackermann adjustment kit included.
  • Adjustable lock stopper.
  • One piece lower control arm desing. 
    2 lower links would have some benefits for circuit racing, but for drifting with higher steering angle the stiffness and packaging would become an issue. Therefore lower one piece arm is used.
  • Higher roll center (RC).
    On Wisefab knuckle, both joints are dropped, which brings the front RC up on lowered car, providing higher roll stiffness and enabling to remove the front anti roll bar (sway bar) that is quite difficult to package with that high lock angles. 
  • Very good camber control and minimal bump steer with high steering angles.
    On drift cars the dynamic camber and bump steer is much more important than static. With Wisefab kinematics we have assured that the camber would provide very good front grip and bump steer is minimal at all the range of steering.
  • Steering jacking control.
    During drifting, when steering angle is much bigger, jacking is also bigger, even with the same geometry and it could become a problem. We have changed the geometry that it doesn’t cause any handling issues.
  • Consistent and predictable self-alignment torque.
    Caster is not the only important parameter to provide sufficient self-alignment torque especially at high lock. It’s the combination of different parameters to maintain consistent trail and self-alignment torque. With our setup the steering wheel turns always to the direction of movement and doesn’t get stuck at full lock. 
  • Adjustable spring and shock absorber motion ratio.
    The shock lower bracket has 3 attachment possibilities, which allows to change suspension stiffness and handling very quickly.

 

Kit includes:

  • Pre-set upper and lower control arms.
  • Knuckles with hardware.
  • Assembeled tie rods.
  • Installation guide.

 

Other components, packaging and clearance.

  • This kit assumes coilovers to have enough clearance.
  • Ride height is designed to be ~80mm from front subframe to ground.
  • Dependent on rim width and ET, wider fenders or fender flares would be needed. Inner wheel wells do not need to be modified with tire diameter up to 635mm (215/45R17, 225/45R17, 235/40R17, 225/40R18 etc).
  • Minimum rim diameter is 17”.
  • Recommended backspacing is ~135mm (7“ ET45; 8“ ET35; 9“ ET20). If ET is smaller, then wheels stay more outwards, if ET is bigger, then spacers need to be used.
  • The kit is designed and manufactured the way that after installation and toe adjustment it’s ready to use right away.
More Information
Make Nissan
Field Drift
Placement Front
Prodmaster Name Lock Kit
color_swatch No
"’We started working together with Wisefab back in 2014 when we launched our Falken Tyres S14 for European competition. Since then, we have enjoyed working closely with the engineers at Wisefab testing new products before going into production and have had a lot of success winning multiple championship worldwide. Thank you to everyone at Wisefab for believing in us and producing such top-quality products."

Spare parts

All
Complete parts
Left Knuckle
Right Knuckle
Left Lower Control Arm
Right Lower Control Arm
Upper Control Arm
Left Tie Rod Assembly
Right Tie Rod Assembly
Hub Center Ring

Complete parts

Complete parts

1
Knuckle
Left
WF370_100LA
$590.00
excluding VAT
Right
WF370_100RA
$590.00
excluding VAT
2
Lower Control Arm
Left
WF350_200LA
$435.00
excluding VAT
Right
WF350_200RA
$435.00
excluding VAT
3
Upper Control Arm
WF370_300A
$250.00
excluding VAT
4
Tie Rod Assembly
Left
WF350_600LA
$110.00
excluding VAT
Right
WF350_600RA
$110.00
excluding VAT
5
Hub Center Ring
WF350_907
$20.00
excluding VAT

Left Knuckle

Left Knuckle

1
Knuckle
Left
WF370_100LA
$590.00
excluding VAT
2
Bolt Allen M12x1.25x 50 RH 12.9 ST DIN 912
B01212125050R4SD912
$9.00
excluding VAT
3
Washer FlatSmall M12 ZN DIN433
B03212NAZD433
$1.80
excluding VAT
4
Bolt Hex M10x1.5x 70 RH 10.9 ST DIN 931
B01110150070R3SD931
$3.40
excluding VAT
5
Washer FlatSmall M10 ZN DIN433
B03210NAZD433
$1.80
excluding VAT
6
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$1.80
excluding VAT
7
Ackermann Washer Round 0 offset
WF013_140
$9.00
excluding VAT
8
Ackermann Washer Round 3 Offset
WF080_142
$9.00
excluding VAT
9
Ackermann Washer Round 6 Offset
WF080_144
$9.00
excluding VAT
10
Bolt Hex M 8x1.25x 70 RH 8.8 ZN DIN 931
B01108125070R2ZD931
$1.80
excluding VAT
11
Washer Flat M 8 ZN DIN125
B03108NAZD125
$1.80
excluding VAT
12
BushingT ID 8 OD22 h51 Excentric Lock Stopper
WF370_950
$14.00
excluding VAT
14
Bolt Hex M12x1.5x 80 RH 10.9 ST DIN 960
B01112150080R3SD960
$8.00
excluding VAT
15
Nut Nylock M12x1.5 RH 8.8 ZN DIN985-8
B02212150R2ZD9858
$1.80
excluding VAT
16
Single Share Mount ID 8 OD12
WF700_903
$30.00
excluding VAT
17
Bolt Allen M 8x1.25x 62.5 RH 12.9 ZN SPC
WF700_904
$30.00
excluding VAT
18
Bolt Allen M 8x1.25x 12 RH 12.9 ST DIN 912
B01208125012R4SD912
$1.80
excluding VAT

Right Knuckle

Right Knuckle

1
Knuckle
Right
WF370_100RA
$590.00
excluding VAT
2
Bolt Allen M12x1.25x 50 RH 12.9 ST DIN 912
B01212125050R4SD912
$9.00
excluding VAT
3
Washer FlatSmall M12 ZN DIN433
B03212NAZD433
$1.80
excluding VAT
4
Bolt Hex M10x1.5x 70 RH 10.9 ST DIN 931
B01110150070R3SD931
$3.40
excluding VAT
5
Washer FlatSmall M10 ZN DIN433
B03210NAZD433
$1.80
excluding VAT
6
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$1.80
excluding VAT
7
Ackermann Washer Round 0 offset
WF013_140
$9.00
excluding VAT
8
Ackermann Washer Round 3 Offset
WF080_142
$9.00
excluding VAT
9
Ackermann Washer Round 6 Offset
WF080_144
$9.00
excluding VAT
10
Bolt Hex M 8x1.25x 70 RH 8.8 ZN DIN 931
B01108125070R2ZD931
$1.80
excluding VAT
11
Washer Flat M 8 ZN DIN125
B03108NAZD125
$1.80
excluding VAT
12
BushingT ID 8 OD22 h51 Excentric Lock Stopper
WF370_950
$14.00
excluding VAT
14
Bolt Hex M12x1.5x 80 RH 10.9 ST DIN 960
B01112150080R3SD960
$8.00
excluding VAT
15
Nut Nylock M12x1.5 RH 8.8 ZN DIN985-8
B02212150R2ZD9858
$1.80
excluding VAT
16
Single Share Mount ID 8 OD12
WF700_903
$30.00
excluding VAT
17
Bolt Allen M 8x1.25x 62.5 RH 12.9 ZN SPC
WF700_904
$30.00
excluding VAT
18
Bolt Allen M 8x1.25x 12 RH 12.9 ST DIN 912
B01208125012R4SD912
$1.80
excluding VAT

Left Lower Control Arm

Left Lower Control Arm

1
Lower Control Arm
Left
WF350_200LA
$435.00
excluding VAT
2
Spacer ID14 OD18 h 3.5
WF370_908
$9.00
excluding VAT
3
Rod end 18x1.5 RH male CrMo
SRODEND18X1.5 RH M
$40.00
excluding VAT
4
BushingT ID20 OD29 h52 SPC
WF350_902
$14.00
excluding VAT
5
Nut Thin M18x1.5 RH 8.8 ZN DIN936/439
B02318150R2ZD936/439
$3.40
excluding VAT
6
Spacer ID14 OD18 h28
WF350_918
$10.00
excluding VAT
7
Spacer ID14 OD18 h23.5
WF370_907
$10.00
excluding VAT
8
Bolt Hex M10x1.5x 35 RH 10.9 ST DIN 933
B01110150035R3SD933
$3.40
excluding VAT
9
Washer Flat M10 ZN DIN125
B03110NAZD125
$1.80
excluding VAT
10
Lower Control Arm Spherical Shock Mount
WF350_700A
$50.00
excluding VAT
11
Spacer ID12 OD16 h11.9
WF113_903
$10.00
excluding VAT
12
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$1.80
excluding VAT
13
Spacer ID12 OD16 h18
WF136_903
$10.00
excluding VAT
14
C-Clip InternalSTD d32 ST DIN472
B04132SD472
$1.80
excluding VAT
15
Spherical ID16/OD32
SSPHERICAL 16/32
$30.00
excluding VAT
16
Spacer ID12 OD16 h 8.5
WF351_904
$9.00
excluding VAT

Right Lower Control Arm

Right Lower Control Arm

1
Lower Control Arm
Right
WF350_200RA
$435.00
excluding VAT
2
Spacer ID14 OD18 h 3.5
WF370_908
$9.00
excluding VAT
3
Rod end 18x1.5 RH male CrMo
SRODEND18X1.5 RH M
$40.00
excluding VAT
4
BushingT ID20 OD29 h52 SPC
WF350_902
$14.00
excluding VAT
5
Nut Thin M18x1.5 RH 8.8 ZN DIN936/439
B02318150R2ZD936/439
$3.40
excluding VAT
6
Spacer ID14 OD18 h28
WF350_918
$10.00
excluding VAT
7
Spacer ID14 OD18 h23.5
WF370_907
$10.00
excluding VAT
8
Bolt Hex M10x1.5x 35 RH 10.9 ST DIN 933
B01110150035R3SD933
$3.40
excluding VAT
9
Washer Flat M10 ZN DIN125
B03110NAZD125
$1.80
excluding VAT
10
Lower Control Arm Spherical Shock Mount
WF350_700A
$50.00
excluding VAT
11
Spacer ID12 OD16 h11.9
WF113_903
$10.00
excluding VAT
12
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$1.80
excluding VAT
13
Spacer ID12 OD16 h18
WF136_903
$10.00
excluding VAT
14
C-Clip InternalSTD d32 ST DIN472
B04132SD472
$1.80
excluding VAT
15
Spherical ID16/OD32
SSPHERICAL 16/32
$30.00
excluding VAT
16
Spacer ID12 OD16 h 8.5
WF351_904
$9.00
excluding VAT

Upper Control Arm

Upper Control Arm

1
Upper Control Arm
WF370_300A
$250.00
excluding VAT
2
Spacer ID10 OD14 h15.5
WF370_901
$10.00
excluding VAT
3
Rod end 14x1.5 LH male CrMo
SRODEND14X1.5 LH M
$25.00
excluding VAT
4
Nut Thin M14x1.5 LH 8.8 ZN DIN936/439
B02314150L2ZD936/439
$3.40
excluding VAT
5
C-Clip InternalSTD d26 ST DIN472
B04126SD472
$1.80
excluding VAT
6
Spherical ID12/OD26
SSPHERICAL 12/26
$30.00
excluding VAT

Left Tie Rod Assembly

Left Tie Rod Assembly

1
Tie Rod Assembly
Left
WF350_600LA
$110.00
excluding VAT
2
Rack Offset Spacer
Left
WF350_801L
$65.00
excluding VAT
3
Bolt Allen M16x1.0x 30 RH 12.9 ZN D912
WF013_913
$15.00
excluding VAT
4
Tie Rod Inner M14x1.5 M14x1.5 L366
STIEROD_M14_M14_L366
$25.00
excluding VAT
5
Spacer ID10 OD14 h13
WF370_909
$10.00
excluding VAT
6
Rod end 14x1.5 RH female CrMo
SRODEND14X1.5 RH F
$35.00
excluding VAT

Right Tie Rod Assembly

Right Tie Rod Assembly

1
Tie Rod Assembly
Right
WF350_600RA
$110.00
excluding VAT
2
Rack Offset Spacer
Right
WF350_801R
$65.00
excluding VAT
3
Bolt Allen M16x1.0x 30 RH 12.9 ZN D912
WF013_913
$15.00
excluding VAT
4
Tie Rod Inner M14x1.5 M14x1.5 L366
STIEROD_M14_M14_L366
$25.00
excluding VAT
5
Spacer ID10 OD14 h13
WF370_909
$10.00
excluding VAT
6
Rod end 14x1.5 RH female CrMo
SRODEND14X1.5 RH F
$35.00
excluding VAT

Hub Center Ring

Image currently unavailable

Hub Center Ring

1
Hub Center Ring
WF350_907
$20.00
excluding VAT