Nissan R33 Front Lock Kit

$1,940.00
excluding VAT
In stock
SKU
WF330
or View Spares

All the metal components on Wisefab Nissan R33 front suspension are from high strenght steel, including sheetmetal components, tube ends and rod end housings. Rod ends and spherical bearings are used, no rubber bushings. 
Top OEM arm is replaced with Wisefab one to have a better kinematics and to avoid rubbing issues at full lock.

Read full description
  • 65 degrees of lock, parallel steering.
    You can tune your steering geometry either towards positive or negative Ackermann in just a few minutes even at trackside without messing up an alignment. 
    Ackermann adjustment kit included.
  • Adjustable lock stopper.
  • One piece design.
    Lower 2 piece arm is replaced with one piece design to increase system stiffness that is needed for high lock.
  • Higher roll center (RC).
    On Wisefab Nissan R-chassis knuckle, both joints are dropped, which brings the front RC up on lowered car, providing higher roll and better camber gain.
  • Very good camber control and minimal bump steer with high steering angles
    On drift cars the dynamic camber and bump steer is much more important than static. With Wisefab kinematics we have assured that the camber would provide very good front grip and bump steer is minimal at all the range of steering.
  • Steering jacking control. 
    During drifting, when steering angle is much bigger, jacking is also bigger, even with the same geometry and it could become a problem. We have changed the geometry so that it doesn't cause any handling issues.
  • Consistent and predictable self-alignment torque. 
    Caster is not the only important parameter to provide sufficient self-alignment torque especially at high lock. It's the combination of different parameters to maintain consistent trail and self-alignment torque. With our setup the steering wheel turns always to the direction of movement and doesn't get stuck at full lock.

Kit includes:

  • Pre-set upper and lower control arms.
  • Knuckles with hardware.
  • Assembeled tie rods.
  • Installation guide.

 

Other components, packaging and clearance.

  • Requires S14 hubs.
  • This kit assumes car to have coilovers to have enough clearance.
  • Ride height is designed to be ~80mm from front subframe to ground.
  • Dependent on rim width and ET, wider fenders or fender flares would be needed.
  • Inner wheel wells do not need to be modified with tire diameter up to 635mm (225/45R17, 235/40R17, 235/35R18, 255/30R18 etc).
  • Minimum rim diameter is 17".
  • Recommended backspacing is ~135mm (7" ET45; 8" ET35; 9" ET20). If ET is smaller, then wheels stay more outwards, if ET is bigger, then spacers need to be used.
  • The kit is designed and manufactured the way that after installation and toe adjustment it's ready to use right away.
More Information
Make Nissan
Field Drift
Placement Front
Prodmaster Name Lock Kit
color_swatch No
"’We started working together with Wisefab back in 2014 when we launched our Falken Tyres S14 for European competition. Since then, we have enjoyed working closely with the engineers at Wisefab testing new products before going into production and have had a lot of success winning multiple championship worldwide. Thank you to everyone at Wisefab for believing in us and producing such top-quality products."

Spare parts

All
Complete parts
Left Knuckle
Right Knuckle
V2 Lower Control Arm
Left Upper Control Arm
Right Upper Control Arm
Left Tie Rod Assembly
Right Tie Rod Assembly

Complete parts

Complete parts

1
Knuckle
Left
WF330_100LA
$370.00
excluding VAT
Right
WF330_100RA
$370.00
excluding VAT
2
V2 Lower Control Arm
WF140_200A
$390.00
excluding VAT
3
Upper Control Arm
Left
WF330_300LA
$285.00
excluding VAT
Right
WF330_300RA
$285.00
excluding VAT
4
Tie Rod Assembly
Left
WF330_600LA
$120.00
excluding VAT
Right
WF330_600RA
$120.00
excluding VAT

Left Knuckle

Left Knuckle

1
Knuckle
Left
WF330_100LA
$370.00
excluding VAT
2
Bolt Hex M10x1.5x 65 RH 10.9 ST DIN 931
B01110150065R3SD931
$3.40
excluding VAT
3
Ackermann Washer Round 0 offset
WF013_140
$9.00
excluding VAT
4
Ackermann Washer Round 3 Offset
WF080_142
$9.00
excluding VAT
5
Ackermann Washer Round 6 Offset
WF080_144
$9.00
excluding VAT
6
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$1.80
excluding VAT
7
Bolt Hex M 8x1.25x 55 RH 8.8 ZN DIN 931
B01108125055R2ZD931
$1.80
excluding VAT
8
BushingT ID 8 OD22 h41 Excentric Lock Stopper
WF350_950
$14.00
excluding VAT
9
Bolt Hex M12x1.5x 60 RH 10.9 ST DIN 960
B01112150060R3SD960
$5.00
excluding VAT
10
Washer FlatSmall M12 ZN DIN433
B03212NAZD433
$1.80
excluding VAT

Right Knuckle

Right Knuckle

1
Knuckle
Right
WF330_100RA
$370.00
excluding VAT
2
Bolt Hex M10x1.5x 65 RH 10.9 ST DIN 931
B01110150065R3SD931
$3.40
excluding VAT
3
Ackermann Washer Round 0 offset
WF013_140
$9.00
excluding VAT
4
Ackermann Washer Round 3 Offset
WF080_142
$9.00
excluding VAT
5
Ackermann Washer Round 6 Offset
WF080_144
$9.00
excluding VAT
6
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$1.80
excluding VAT
7
Bolt Hex M 8x1.25x 55 RH 8.8 ZN DIN 931
B01108125055R2ZD931
$1.80
excluding VAT
8
BushingT ID 8 OD22 h41 Excentric Lock Stopper
WF350_950
$14.00
excluding VAT
9
Bolt Hex M12x1.5x 60 RH 10.9 ST DIN 960
B01112150060R3SD960
$5.00
excluding VAT
10
Washer FlatSmall M12 ZN DIN433
B03212NAZD433
$1.80
excluding VAT

V2 Lower Control Arm

V2 Lower Control Arm

1
V2 Lower Control Arm
WF140_200A
$390.00
excluding VAT
2
V2 Lower Control Arm Fixing
WF140_210A
$110.00
excluding VAT
3
Spacer ID14 OD16 h21
WF013_902
$10.00
excluding VAT
4
Rod end 16x1.5 RH male CrMo
SRODEND16X1.5 RH M
$35.00
excluding VAT
5
Nut Thin M16x1.5 RH 8.8 ZN DIN936/439
B02316150R2ZD936/439
$3.40
excluding VAT
6
Spacer ID12 OD16 h10
WF013_903
$10.00
excluding VAT
7
C-Clip InternalSTD d32 ST DIN472
B04132SD472
$1.80
excluding VAT
8
Spherical ID16/OD32
SSPHERICAL 16/32
$30.00
excluding VAT

Left Upper Control Arm

Left Upper Control Arm

1
Upper Control Arm
Left
WF330_300LA
$285.00
excluding VAT
2
Spacer ID12 OD16 h11.9
WF113_903
$10.00
excluding VAT
3
Rod end 16x1.5 RH male CrMo
SRODEND16X1.5 RH M
$35.00
excluding VAT
4
Nut Thin M16x1.5 RH 8.8 ZN DIN936/439
B02316150R2ZD936/439
$3.40
excluding VAT
5
BushingT ID12.5 OD26 h103
WF330_904
$14.00
excluding VAT
6
BushingPOM ID26 OD40 h45
WF330_905
$13.00
excluding VAT

Right Upper Control Arm

Right Upper Control Arm

1
Upper Control Arm
Right
WF330_300RA
$285.00
excluding VAT
2
Spacer ID12 OD16 h11.9
WF113_903
$10.00
excluding VAT
3
Rod end 16x1.5 RH male CrMo
SRODEND16X1.5 RH M
$35.00
excluding VAT
4
Nut Thin M16x1.5 RH 8.8 ZN DIN936/439
B02316150R2ZD936/439
$3.40
excluding VAT
5
BushingT ID12.5 OD26 h103
WF330_904
$14.00
excluding VAT
6
BushingPOM ID26 OD40 h45
WF330_905
$13.00
excluding VAT

Left Tie Rod Assembly

Left Tie Rod Assembly

1
Tie Rod Assembly
Left
WF330_600LA
$120.00
excluding VAT
2
Rack Offset Spacer
Left
WF330_800LA
$65.00
excluding VAT
3
Bolt Allen M16x1.0x 30 RH 12.9 ZN D912
WF013_913
$15.00
excluding VAT
4
Tie Rod Inner M14x1.5 M14x1.5 L360
STIEROD_M14_M14_L360
$25.00
excluding VAT
5
Spacer ID10 OD14 h11
WF013_901
$9.00
excluding VAT
6
Rod end 14x1.5 RH female CrMo
SRODEND14X1.5 RH F
$35.00
excluding VAT

Right Tie Rod Assembly

Right Tie Rod Assembly

1
Tie Rod Assembly
Right
WF330_600RA
$120.00
excluding VAT
2
Rack Offset Spacer
Right
WF330_800RA
$65.00
excluding VAT
3
Bolt Allen M16x1.0x 30 RH 12.9 ZN D912
WF013_913
$15.00
excluding VAT
4
Tie Rod Inner M14x1.5 M14x1.5 L360
STIEROD_M14_M14_L360
$25.00
excluding VAT
5
Spacer ID10 OD14 h11
WF013_901
$9.00
excluding VAT
6
Rod end 14x1.5 RH female CrMo
SRODEND14X1.5 RH F
$35.00
excluding VAT