Nissan S14 Front V2 Lock Kit with Rack Relocation

$1,980.00
excluding VAT
In stock
SKU
WF140 INS
or View Spares

Wisefab Nissan S-Chassis 2 front suspension kit. Legendary kit has an upgrade, more usable lock with better feel and precise handling. More droop built in the suspension kit with longstroke coilovers equals more grip in extreme racing situations.

Read full description
  • More usable lock.
    65+ degrees of lock, better feel and precise handling. You could tune your steering geometry either towards positive or negative Ackermann in just a few minutes even at trackside without messing up an alignment. 
    Ackermann adjustment kit included.
  • Less sensitive steering.
    Increased steering ratio for smooth handling.
  • More suspension travel.
    Less interference risk at full droop. Longstroke coilover kits can be used.
  • Lighter and stronger.
    Optimized design in combination with high strenght steel is used.
  • Higher roll center (RC).
    On Wisefab knuckle, the ball joint is lowered 60mm, which brings the front RC up on lowered car, providing higher roll stiffness and letting to remove the front anti roll bar (sway bar) that is quite difficult to package with that high lock angles.
  • Adjustable camber and caster with adjustable doubleplates.
  • Adjustable lock stopper.
  • One piece lower control arm desing. 
    Lower links are replaced with one arm. Drifting with higher steering angle the stiffness and packaging would become an issue. Therefore lower one piece arm is used.
  • Very good camber control and minimal bump steer with high steering angles. 
    On drift cars the dynamic camber and bump steer is much more important than static. With our kinematics we have assured that the camber would provide very good front grip and bump steer is minimal at all the range of steering.
    • Steering jacking control.
      During drifting, when steering angle is much bigger, jacking is also bigger, even with the same geometry and it could become a problem. We have changed the geometry that it doesn’t cause any handling issues.
    • Consistent and predictable self-alignment torque. 
      Caster is not the only important parameter to provide sufficient self-alignment torque especially at high lock. It’s the combination of different parameters to maintain consistent trail and self-alignment torque. With our setup the steering wheel turns always to the direction of movement and doesn’t get stuck at full lock. 

Kit includes:

  • Adjustable coilover upper mounts, Formula Drift compliance.
  • Knuckles with hardware.
  • Lower control arms.
  • Assembeled tie rods.
  • Rack relocating kit.
  • Rack installation guide.
  • Installation guide.

 

Other components, packaging and clearance.

  • This kit assumes coilovers to have enough clearance.
  • Dependent on rim width and ET, wider fenders or fender flares would be needed.
  • With tire diameter up to 635mm (215/45R17, 225/45R17, 235/40R17, 225/40R18 etc) and lowered ride height the inner wheel wells need to be slightly modified.
  • Recommended backspacing is 135-140mm (7“ ET45; 8“ ET35; 9“ ET25).If ET is smaller, then wheels stay more outwards, if ET is bigger, then spacers need to be used.
More Information
Make Nissan
Field Drift
Placement Front
Prodmaster Name V2 Lock Kit with Rack Relocation
color_swatch No
"’We started working together with Wisefab back in 2014 when we launched our Falken Tyres S14 for European competition. Since then, we have enjoyed working closely with the engineers at Wisefab testing new products before going into production and have had a lot of success winning multiple championship worldwide. Thank you to everyone at Wisefab for believing in us and producing such top-quality products."

Spare parts

All
Complete parts
Left V2 Knuckle
Right V2 Knuckle
V2 Lower Control Arm
V2 Tie Rod Assembly
Left V2 Top Mount
Right V2 Top Mount
V2 Rack Relocation Insert

Complete parts

Complete parts

1
V2 Knuckle
Left
WF140_100LA
$370.00
excluding VAT
Right
WF140_100RA
$370.00
excluding VAT
2
V2 Lower Control Arm
WF140_200A
$390.00
excluding VAT
3
V2 Tie Rod Assembly
WF140_600A
$85.00
excluding VAT
4
V2 Top Mount
Left
WF140_500LA
$140.00
excluding VAT
Right
WF140_500RA
$140.00
excluding VAT
5
V2 Rack Relocation Insert
WF149_000A
$225.00
excluding VAT

Left V2 Knuckle

Left V2 Knuckle

1
V2 Knuckle
Left
WF140_100LA
$370.00
excluding VAT
2
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$1.80
excluding VAT
3
Ackermann Washer Round 0 offset
WF013_140
$9.00
excluding VAT
4
Ackermann Washer Round 3 Offset
WF080_142
$9.00
excluding VAT
5
Ackermann Washer Round 6 Offset
WF080_144
$9.00
excluding VAT
6
BushingT ID10 OD24 h10
WF901_905
$9.00
excluding VAT
7
Bolt Hex M10x1.5x 75 RH 10.9 ST DIN 931
B01110150075R3SD931
$3.40
excluding VAT
8
Bolt Hex M 8x1.25x 70 RH 8.8 ZN DIN 931
B01108125070R2ZD931
$1.80
excluding VAT
9
BushingT ID 8 OD22 h51 Excentric Lock Stopper
WF370_950
$14.00
excluding VAT
10
Nut Nylock M 8x1.25 RH 8.8 ZN DIN985-8
B02208125R2ZD9858
$1.80
excluding VAT
11
Bolt Hex M12x1.5x 70 RH 10.9 ST DIN 960
B01112150070R3SD960
$8.00
excluding VAT
12
Washer Flat M12 ZN DIN125
B03112NAZD125
$1.80
excluding VAT
13
BushingT ID12 OD14 h28
WF013_918
$10.00
excluding VAT

Right V2 Knuckle

Right V2 Knuckle

1
V2 Knuckle
Right
WF140_100RA
$370.00
excluding VAT
2
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$1.80
excluding VAT
3
Ackermann Washer Round 0 offset
WF013_140
$9.00
excluding VAT
4
Ackermann Washer Round 3 Offset
WF080_142
$9.00
excluding VAT
5
Ackermann Washer Round 6 Offset
WF080_144
$9.00
excluding VAT
6
BushingT ID10 OD24 h10
WF901_905
$9.00
excluding VAT
7
Bolt Hex M10x1.5x 75 RH 10.9 ST DIN 931
B01110150075R3SD931
$3.40
excluding VAT
8
Bolt Hex M 8x1.25x 70 RH 8.8 ZN DIN 931
B01108125070R2ZD931
$1.80
excluding VAT
9
BushingT ID 8 OD22 h51 Excentric Lock Stopper
WF370_950
$14.00
excluding VAT
10
Nut Nylock M 8x1.25 RH 8.8 ZN DIN985-8
B02208125R2ZD9858
$1.80
excluding VAT
11
Bolt Hex M12x1.5x 70 RH 10.9 ST DIN 960
B01112150070R3SD960
$8.00
excluding VAT
12
Washer Flat M12 ZN DIN125
B03112NAZD125
$1.80
excluding VAT
13
BushingT ID12 OD14 h28
WF013_918
$10.00
excluding VAT

V2 Lower Control Arm

V2 Lower Control Arm

1
V2 Lower Control Arm
WF140_200A
$390.00
excluding VAT
2
V2 Lower Control Arm Fixing
WF140_210A
$110.00
excluding VAT
3
Spacer ID14 OD16 h21
WF013_902
$10.00
excluding VAT
4
Rod end 16x1.5 RH male CrMo
SRODEND16X1.5 RH M
$35.00
excluding VAT
5
Nut Thin M16x1.5 RH 8.8 ZN DIN936/439
B02316150R2ZD936/439
$3.40
excluding VAT
6
Spacer ID12 OD16 h10
WF013_903
$10.00
excluding VAT
7
C-Clip InternalSTD d32 ST DIN472
B04132SD472
$1.80
excluding VAT
8
Spherical ID16/OD32
SSPHERICAL 16/32
$30.00
excluding VAT

V2 Tie Rod Assembly

V2 Tie Rod Assembly

1
V2 Tie Rod Assembly
WF140_600A
$85.00
excluding VAT
2
Tie Rod Inner M14x1.5 M14x1.5 L360
STIEROD_M14_M14_L360
$25.00
excluding VAT
3
Spacer ID10 OD14 h11
WF013_901
$9.00
excluding VAT
4
Rod end 14x1.5 RH female CrMo
SRODEND14X1.5 RH F
$35.00
excluding VAT

Left V2 Top Mount

Left V2 Top Mount

1
V2 Top Mount
Left
WF140_500LA
$140.00
excluding VAT
2
Bolt Hex M10x1.5x 30 RH 10.9 ST DIN 933
B01110150030R3SD933
$3.40
excluding VAT
3
Camber Plate Spherical Housing REG
WF013_917A
$65.00
excluding VAT
4
Pin Spring 6x10 Normal ST DIN1481
B05206010NSD1481
$1.80
excluding VAT
5
V2 Top Mount Spacer Plate
WF140_503
$30.00
excluding VAT
6
Nut Hex Flange M10x1.5 RH 8.8 ZN
B02510150R2ZD69238
$3.40
excluding VAT
7
Bolt AllenFlat M 6x1.0x 16 RH 8.8 ZN DIN7991
B01306100016R2SD7991
$1.80
excluding VAT

Right V2 Top Mount

Right V2 Top Mount

1
V2 Top Mount
Right
WF140_500RA
$140.00
excluding VAT
2
Bolt Hex M10x1.5x 30 RH 10.9 ST DIN 933
B01110150030R3SD933
$3.40
excluding VAT
3
Camber Plate Spherical Housing REG
WF013_917A
$65.00
excluding VAT
4
Pin Spring 6x10 Normal ST DIN1481
B05206010NSD1481
$1.80
excluding VAT
5
V2 Top Mount Spacer Plate
WF140_503
$30.00
excluding VAT
6
Nut Hex Flange M10x1.5 RH 8.8 ZN
B02510150R2ZD69238
$3.40
excluding VAT
7
Bolt AllenFlat M 6x1.0x 16 RH 8.8 ZN DIN7991
B01306100016R2SD7991
$1.80
excluding VAT

V2 Rack Relocation Insert

V2 Rack Relocation Insert

1
V2 Rack Relocation Insert
WF149_000A
$225.00
excluding VAT
1
Bolt Hex M14x1.5x 80 RH 10.9 ST DIN 960
B01114150080R3SD960
$10.00
excluding VAT
2
Washer FlatSmall M14 ZN DIN433
B03214NAZD433
$1.80
excluding VAT
3
Bolt Hex M 8x1.25x 16 RH 8.8 ZN DIN 933
B01108125016R2ZD933
$1.80
excluding VAT
4
V2 Rack Relocation Clamp 1
WF149_010
$40.00
excluding VAT
5
V2 Rack Relocation Clamp 2
WF149_020
$40.00
excluding VAT
6
V2 Rack Insert Bushing
WF149_901
$19.00
excluding VAT
7
V2 Rack Insert Sleeve
WF149_902
$23.00
excluding VAT
8
V2 Steering Column Extender Assembly
WF149_040A
$165.00
excluding VAT
9
Rack Extender M14x1.5 M16x1.0 L24
WFR70_905
$23.00
excluding VAT