Toyota Soarer Front Lock Kit

$2,100.00
excluding VAT
In stock
SKU
WF080
or View Spares

The main objective of this Wisefab Toyota Supra front suspension kit is to provide more grip on lowered car, parallel steering and more usable lock. All the metal components on Supra front suspension are from high strenght steel, including sheetmetal components, tube ends and rod end housings. Rod ends and spherical bearings are used, no rubber bushings.

Read full description
  • 65 degrees of lock, parallel steering.
    Both wheels turn the same angle. You could tune your steering geometry either towards positive or negative Ackermann in just a few minutes even at trackside without messing up an alignment. 
    Ackermann adjustment kit included.
  • Higher roll center (RC). 
    On Wisefab knuckle, both joints have lowered about 60mm, which brings the front RC up on lowered car, providing higher roll stiffness and letting to remove the front anti roll bar (sway bar) that is quite difficult to package with that high lock angles.
  • Very good camber control and minimal bump steer with high steering angles. 
    On drift cars the dynamic camber and bump steer is much more important than static. With our kinematics we have assured that the camber would provide very good front grip and bump steer is minimal at all the range of steering.
  • Steering jacking control.
    During drifting, when steering angle is much bigger, jacking is also bigger, even with the same geometry and it could become a problem. We have changed the geometry that it doesn’t cause any handling issues.
  • Consistent and predictable self-alignment torque. 
    Caster is not the only important parameter to provide sufficient self-alignment torque especially at high lock. It’s the combination of different parameters to maintain consistent trail and self-alignment torque. With our setup the steering wheel turns always to the direction of movement and doesn’t get stuck at full lock.
  • Adjustable spring and shock absorber motion ratio. 
    The shock lower bracket has 3 attachment possibilities, which allows to change suspension stiffness and handling very quickly without changing the spring and messing up ride heights.

 

 

Kit includes:

  • Pre-set suspension control arms.
  • Knuckles with hardware.
  • Installation guide.

 

Other components, packaging and clearance:

  • This kit assumes coilovers to have enough clearance.
  • Ride height is designed to be ~80mm from front subframe to ground.
  • Dependent on rim width and ET, wider fenders or fender flares would be needed.
  • Inner wheel wells need to be slightly modified with tire diameter up to 635mm (215/45R17, 225/45R17, 235/40R17, 225/40R18 etc).
  • Minimum rim diameter is 17”.Recommended backspacing is ~135mm (7“ ET45; 8“ ET35; 9“ ET20).
  • If ET is smaller, then wheels stay more outwards, if ET is bigger, then spacers need to be used.
  • The kit is designed and manufactured the way that after installation and toe adjustment it’s ready to use right away.
More Information
Make Toyota
Field Drift
Placement Front
Prodmaster Name Lock Kit
color_swatch No
"’We started working together with Wisefab back in 2014 when we launched our Falken Tyres S14 for European competition. Since then, we have enjoyed working closely with the engineers at Wisefab testing new products before going into production and have had a lot of success winning multiple championship worldwide. Thank you to everyone at Wisefab for believing in us and producing such top-quality products."

Spare parts

All
Complete parts
Left Knuckle
Right Knuckle
Left Lower Control Arm
Right Lower Control Arm
Upper Control Arm
Tie Rod Assembly

Complete parts

Complete parts

1
Knuckle
Left
WF080_100LA
$450.00
excluding VAT
Right
WF080_100RA
$450.00
excluding VAT
2
Lower Control Arm
Left
WF080_200LA
$390.00
excluding VAT
Right
WF080_200RA
$390.00
excluding VAT
3
Upper Control Arm
WF080_300A
$285.00
excluding VAT
4
Tie Rod Assembly
WF080_600A
$85.00
excluding VAT

Left Knuckle

Left Knuckle

1
Knuckle
Left
WF080_100LA
$450.00
excluding VAT
2
Bolt AllenButton M 8x1.25x 60 RH 8.8 ZN ISO7380
B01408125060R2ZI7380
$3.40
excluding VAT
3
BushingT ID 8 OD22 h46
WF080_922
$13.00
excluding VAT
4
Nut Nylock M 8x1.25 RH 8.8 ZN DIN985-8
B02208125R2ZD9858
$1.80
excluding VAT
5
Bolt Hex M14x1.5x 80 RH 10.9 ST DIN 960
B01114150080R3SD960
$10.00
excluding VAT
6
Washer FlatSmall M14 ZN DIN433
B03214NAZD433
$1.80
excluding VAT
7
Nut Nylock M14x1.5 RH 8.8 ZN DIN985-8
B02214150R2ZD9858
$1.80
excluding VAT
8
Bolt Hex M10x1.5x 65 RH 10.9 ST DIN 931
B01110150065R3SD931
$3.40
excluding VAT
9
BushingT ID 8 OD16 h46
WF080_923
$10.00
excluding VAT
10
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$1.80
excluding VAT
11
Washer FlatSmall M10 ZN DIN433
B03210NAZD433
$1.80
excluding VAT
12
Ackermann Washer Round 0 offset
WF013_140
$9.00
excluding VAT
13
Ackermann Washer Round 3 Offset
WF080_142
$9.00
excluding VAT
14
Ackermann Washer Round 4.5 Offset
WF080_143
$9.00
excluding VAT
15
Bolt Hex M10x1.5x 60 RH 10.9 ST DIN 931
B01110150060R3SD931
$3.40
excluding VAT

Right Knuckle

Right Knuckle

1
Knuckle
Right
WF080_100RA
$450.00
excluding VAT
2
Bolt AllenButton M 8x1.25x 60 RH 8.8 ZN ISO7380
B01408125060R2ZI7380
$3.40
excluding VAT
3
BushingT ID 8 OD22 h46
WF080_922
$13.00
excluding VAT
4
Nut Nylock M 8x1.25 RH 8.8 ZN DIN985-8
B02208125R2ZD9858
$1.80
excluding VAT
5
Bolt Hex M14x1.5x 80 RH 10.9 ST DIN 960
B01114150080R3SD960
$10.00
excluding VAT
6
Washer FlatSmall M14 ZN DIN433
B03214NAZD433
$1.80
excluding VAT
7
Nut Nylock M14x1.5 RH 8.8 ZN DIN985-8
B02214150R2ZD9858
$1.80
excluding VAT
8
Bolt Hex M10x1.5x 65 RH 10.9 ST DIN 931
B01110150065R3SD931
$3.40
excluding VAT
9
BushingT ID 8 OD16 h46
WF080_923
$10.00
excluding VAT
10
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$1.80
excluding VAT
11
Washer FlatSmall M10 ZN DIN433
B03210NAZD433
$1.80
excluding VAT
12
Ackermann Washer Round 0 offset
WF013_140
$9.00
excluding VAT
13
Ackermann Washer Round 3 Offset
WF080_142
$9.00
excluding VAT
14
Ackermann Washer Round 4.5 Offset
WF080_143
$9.00
excluding VAT
15
Bolt Hex M10x1.5x 60 RH 10.9 ST DIN 931
B01110150060R3SD931
$3.40
excluding VAT

Left Lower Control Arm

Left Lower Control Arm

1
Lower Control Arm
Left
WF080_200LA
$390.00
excluding VAT
2
Spacer ID16 OD18 h23.7
WF080_901
$10.00
excluding VAT
3
Rod end 18x1.5 RH male CrMo
SRODEND18X1.5 RH M
$40.00
excluding VAT
4
Nut Thin M18x1.5 RH 8.8 ZN DIN936/439
B02318150R2ZD936/439
$3.40
excluding VAT
5
Spacer ID16 OD18 h22.25
WF080_902
$10.00
excluding VAT
6
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$1.80
excluding VAT
7
Washer FlatSmall M10 ZN DIN433
B03210NAZD433
$1.80
excluding VAT
8
Lower Control Arm Shock Mount
WF080_220
$24.00
excluding VAT
9
Bolt Hex M10x1.5x 35 RH 10.9 ST DIN 933
B01110150035R3SD933
$3.40
excluding VAT
10
Spacer ID14 OD18 h 8.5
WF080_903
$10.00
excluding VAT
11
C-Clip InternalSTD d35 ST DIN472
B04135SD472
$1.80
excluding VAT
12
Spherical ID18/OD35
SSPHERICAL 18/35
$35.00
excluding VAT

Right Lower Control Arm

Right Lower Control Arm

1
Lower Control Arm
Right
WF080_200RA
$390.00
excluding VAT
2
Spacer ID16 OD18 h23.7
WF080_901
$10.00
excluding VAT
3
Rod end 18x1.5 RH male CrMo
SRODEND18X1.5 RH M
$40.00
excluding VAT
4
Nut Thin M18x1.5 RH 8.8 ZN DIN936/439
B02318150R2ZD936/439
$3.40
excluding VAT
5
Spacer ID16 OD18 h22.25
WF080_902
$10.00
excluding VAT
6
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$1.80
excluding VAT
7
Washer FlatSmall M10 ZN DIN433
B03210NAZD433
$1.80
excluding VAT
8
Lower Control Arm Shock Mount
WF080_220
$24.00
excluding VAT
9
Bolt Hex M10x1.5x 35 RH 10.9 ST DIN 933
B01110150035R3SD933
$3.40
excluding VAT
10
Spacer ID14 OD18 h 8.5
WF080_903
$10.00
excluding VAT
11
C-Clip InternalSTD d35 ST DIN472
B04135SD472
$1.80
excluding VAT
12
Spherical ID18/OD35
SSPHERICAL 18/35
$35.00
excluding VAT

Upper Control Arm

Upper Control Arm

1
Upper Control Arm
WF080_300A
$285.00
excluding VAT
2
Nut Special M14x1.50 RH ZN SPC
WF080_908
$15.00
excluding VAT
3
Rod end 16x1.5 RH male CrMo
SRODEND16X1.5 RH M
$35.00
excluding VAT
4
Spacer ID14 OD16 h 4.5
WF080_909
$9.00
excluding VAT
5
Nut Thin M16x1.5 RH 8.8 ZN DIN936/439
B02316150R2ZD936/439
$3.40
excluding VAT
6
Bolt Allen M14x1.50x200 RH 12.9 ST SPC
WF080_907
$40.00
excluding VAT
7
Spacer ID10 OD12 h14
WF080_906
$10.00
excluding VAT
8
C-Clip InternalSTD d26 ST DIN472
B04126SD472
$1.80
excluding VAT
9
Spherical ID12/OD26
SSPHERICAL 12/26
$30.00
excluding VAT

Tie Rod Assembly

Tie Rod Assembly

1
Tie Rod Assembly
WF080_600A
$85.00
excluding VAT
2
Tie Rod Inner M14x1.5 M14x1.5 L366
STIEROD_M14_M14_L366
$25.00
excluding VAT
3
Spacer ID10 OD14 h 5.4
WF080_921
$9.00
excluding VAT
4
Rod end 14x1.5 RH female CrMo
SRODEND14X1.5 RH F
$35.00
excluding VAT