BMW E46 M3 Front Drift Angle Lock Kit

$1,240.00
excluding VAT
In stock
SKU
WF046M
or View Spares

Over 60 degrees of lock. The most important parameter that everybody is speaking in drifting is lock – we have it! While providing over 60 degrees of lock, this kit is engineered and tested to optimize also a lot of other parameters that make the difference in handling and performance.

Read full description
  • Higher roll center
    Wisefab suspension kit brings the front roll center up on lowered cars, providing higher roll stiffness and letting to remove the front anti roll bar (swaybar) enabling maximum usable lock.
  • Revised steering geometry (Ackermann)
    Normally in a corner the inner wheel has a greater angle than the outer. For drifting this means loss of speed and grip and we have correted this for best performance.
  • Good camber control with high steering angles
    With high steering angles the leading wheel will have a positive camber, which is not a positive effect. It reduces the front grip and during turn or flip it creates a contact patch transition from inside edge to outside edge. It is not possible to eliminate it, but with our geometry it has decreased as much as possible.
  • Steering jacking control
    During drifting, when steering angle is much bigger, jacking is also bigger, even with the same geometry and it could become a problem. We have monitored it and changed the geometry that it doesn’t cause any handling issues.
  • Predictable self-alignment control
    With certain suspension geometry at high steering angles it could happen that the steering wheel is locking up at the end and driver needs to apply some force to flip it to other side. We know what causes it and have decreased it to minimum, if not eliminated it.

Kit includes:

  • Adjustable coilover upper mounts, Formula Drift compliance.
  • Hub add-ons with hardware.
  • Lightweight lower control arms.
  • Assembeled tie rods.
  • Adjustable lower control arm rear mount.
  • Installation guide

Other components, packaging and clearance. 

  • This kit assumes coilovers to have enough clearance. 
  • We recommend tire diameter not bigger than 620mm (235/40 R17). 
  • Wider fenders or fender flares needed with this kit.
More Information
Make BMW
Field Drift
Placement Front
Prodmaster Name Drift Angle Lock Kit
color_swatch No
"’We started working together with Wisefab back in 2014 when we launched our Falken Tyres S14 for European competition. Since then, we have enjoyed working closely with the engineers at Wisefab testing new products before going into production and have had a lot of success winning multiple championship worldwide. Thank you to everyone at Wisefab for believing in us and producing such top-quality products."

Spare parts

All
Complete parts
Left Knuckle Add-on
Right Knuckle Add-on
Left Lower Control Arm
Right Lower Control Arm
Tierod Assembly
Left Top Mount
Right Top Mount
Left Control Arm Mount
Right Control Arm Mount

Complete parts

Complete parts

1
Knuckle Add-on
Left
WF046M_100LA
$250.00
excluding VAT
Right
WF046M_100RA
$250.00
excluding VAT
2
Lower Control Arm
Left
WF036_200LA
$370.00
excluding VAT
Right
WF036_200RA
$370.00
excluding VAT
3
Tierod Assembly
WF036_600A
$100.00
excluding VAT
4
Top Mount
Left
WF046_500LA
$125.00
excluding VAT
Right
WF046_500RA
$125.00
excluding VAT
5
Control Arm Mount
Left
WF046_400LA
$85.00
excluding VAT
Right
WF046_400RA
$85.00
excluding VAT

Left Knuckle Add-on

Left Knuckle Add-on

1
Knuckle Add-on
Left
WF046M_100LA
$250.00
excluding VAT
2
Conical Bolt D18 L63
WF046_901
$13.00
excluding VAT
3
Conical Bolt D16.4 L63
WF030_901
$14.00
excluding VAT
4
Nut Nylock M12x1.5 RH 8.8 ZN DIN985-8
B02212150R2ZD9858
$1.80
excluding VAT
5
Nut Hex Flange M10x1.5 RH 8.8 ZN
B02510150R2ZD69238
$3.40
excluding VAT
6
Bolt Hex M14x1.5x 70 RH 10.9 ST DIN 960
B01114150070R3SD960
$8.00
excluding VAT

Right Knuckle Add-on

Right Knuckle Add-on

1
Knuckle Add-on
Right
WF046M_100RA
$250.00
excluding VAT
2
Conical Bolt D18 L63
WF046_901
$13.00
excluding VAT
3
Conical Bolt D16.4 L63
WF030_901
$14.00
excluding VAT
4
Nut Nylock M12x1.5 RH 8.8 ZN DIN985-8
B02212150R2ZD9858
$1.80
excluding VAT
5
Nut Hex Flange M10x1.5 RH 8.8 ZN
B02510150R2ZD69238
$3.40
excluding VAT
6
Bolt Hex M14x1.5x 70 RH 10.9 ST DIN 960
B01114150070R3SD960
$8.00
excluding VAT

Left Lower Control Arm

Left Lower Control Arm

1
Lower Control Arm
Left
WF036_200LA
$370.00
excluding VAT
2
Bolt Allen M12x1.50x 12.5 RH 12.9 ZN
WF036_911
$24.00
excluding VAT
3
BushingT ID 8 OD22 h51 Excentric Lock Stopper
WF036_913
$23.00
excluding VAT
4
Bolt Allen M10x1.5x 55 RH 8.8 ZN DIN 912
B01210150055R2ZD912
$1.80
excluding VAT
5
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$1.80
excluding VAT
6
Spacer ID14 OD16 h10 SPC
WF036_908
$10.00
excluding VAT
7
C-Clip InternalSTD d32 ST DIN472
B04132SD472
$1.80
excluding VAT
8
Spherical ID16/OD32
SSPHERICAL 16/32
$30.00
excluding VAT
9
Spacer ID14 OD16 h10
WF036_903
$10.00
excluding VAT
10
Nut Nylock M14x1.5 RH 8.8 ZN DIN985-8
B02214150R2ZD9858
$1.80
excluding VAT
11
Control Arm Inner Joint Shaft V2
WF036_920
$25.00
excluding VAT

Right Lower Control Arm

Right Lower Control Arm

1
Lower Control Arm
Right
WF036_200RA
$370.00
excluding VAT
2
Bolt Allen M12x1.50x 12.5 RH 12.9 ZN
WF036_911
$24.00
excluding VAT
3
BushingT ID 8 OD22 h51 Excentric Lock Stopper
WF036_913
$23.00
excluding VAT
4
Bolt Allen M10x1.5x 55 RH 8.8 ZN DIN 912
B01210150055R2ZD912
$1.80
excluding VAT
5
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$1.80
excluding VAT
6
Spacer ID14 OD16 h10 SPC
WF036_908
$10.00
excluding VAT
7
C-Clip InternalSTD d32 ST DIN472
B04132SD472
$1.80
excluding VAT
8
Spherical ID16/OD32
SSPHERICAL 16/32
$30.00
excluding VAT
9
Spacer ID14 OD16 h10
WF036_903
$10.00
excluding VAT
10
Nut Nylock M14x1.5 RH 8.8 ZN DIN985-8
B02214150R2ZD9858
$1.80
excluding VAT
11
Control Arm Inner Joint Shaft V2
WF036_920
$25.00
excluding VAT

Tierod Assembly

Tierod Assembly

1
Tierod Assembly
WF036_600A
$100.00
excluding VAT
2
Tie Rod Extension
WF036_904
$40.00
excluding VAT
3
Rod end 14x1.5 RH female CrMo
SRODEND14X1.5 RH F
$35.00
excluding VAT
4
Nut Collar M12x1.50 RH ZN SPC
WF001_12X15
$10.00
excluding VAT
5
Conical Bolt D16.4 L66
WF036_909
$18.00
excluding VAT
6
Spacer ID10 OD14 h 5.4
WF080_921
$9.00
excluding VAT
7
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$1.80
excluding VAT

Left Top Mount

Left Top Mount

1
Top Mount
Left
WF046_500LA
$125.00
excluding VAT
2
Camber Plate Spherical Housing REG
WF013_917A
$65.00
excluding VAT
3
Bolt HexFlange M 8x1.25x 10 RH 10.9 ZN DIN6921
B01608125010R2ZD6921
$3.40
excluding VAT
4
Bolt AllenFlat M 6x1.0x 16 RH 8.8 ZN DIN7991
B01306100016R2SD7991
$1.80
excluding VAT

Right Top Mount

Right Top Mount

1
Top Mount
Right
WF046_500RA
$125.00
excluding VAT
2
Camber Plate Spherical Housing REG
WF013_917A
$65.00
excluding VAT
3
Bolt HexFlange M 8x1.25x 10 RH 10.9 ZN DIN6921
B01608125010R2ZD6921
$3.40
excluding VAT
4
Bolt AllenFlat M 6x1.0x 16 RH 8.8 ZN DIN7991
B01306100016R2SD7991
$1.80
excluding VAT

Left Control Arm Mount

Left Control Arm Mount

1
Control Arm Mount
Left
WF046_400LA
$85.00
excluding VAT
2
Rod end 20x1.5 RH male CrMo
SRODEND 20X1.5 RH M
$40.00
excluding VAT
3
Nut Thin M20x1.5 RH 8.8 ZN DIN936/439
B02320150R2ZD936/439
$3.40
excluding VAT

Right Control Arm Mount

Right Control Arm Mount

1
Control Arm Mount
Right
WF046_400RA
$85.00
excluding VAT
2
Rod end 20x1.5 RH male CrMo
SRODEND 20X1.5 RH M
$40.00
excluding VAT
3
Nut Thin M20x1.5 RH 8.8 ZN DIN936/439
B02320150R2ZD936/439
$3.40
excluding VAT